connections | Page 6

connections

  1. J

    Bosch/Neff Ceramic Hotplate Connections

    Hi, I'm trying to replace one of the hotplate elements (Bosch 180mm 2000w hilight 644726) on my Neff Hob (T1373S0/01). I've received the replacement part but the new one has 5 connections on the wiring block compared to 2 on the old one as you can hopefully see on the pics. I suspect the...
  2. H

    Connections to vaillant eco tec pro 28 boiler!

    Hi, I have a job to connect Honeywell T6360 Room Stat & a Honeywell ST9100S programmer to a Vaillant eco tec pro 28 combi boiler. From the programmer I have taken a feed to the thermostat, as per the programmer drawing, from the stat my switch wire then goes to the RT 230V terminal on the...
  3. A

    Oven & Hob Connections

    Hi, I'm a builder fitting a new kitchen for myself and need a little advise please. I am putting in all the back boxes and cables in the wall to save a little money but unsure on the cooker side of things. I have put 6mm T&E cable to cooker switch above worktops (which will come directly from...
  4. C

    Single Phase Motor Connections

    Hi guys, got a single phase motor to install tomorrow. Its a Ebara 1.5kw capacitor start capacitor run type. Have fitted single phase motors of this type before however there is more wires at the terminal box of this particular type and not quite sure about the connections. The terminal box lid...
  5. S

    high integrity board layout - Is this Ok?

    Hi, I have looked inside my Dad's Consumer Unit and I noticed that it has 2 RCD's but also 1 RCBO. I've seen these before but on my dads I was worried that it has to many (live) terminations into the bottom of the main switch? It has the usual 2 live conductors (wires) in it each going off to...
  6. L

    Kva ratings for meter connections

    Hi there, Im new to the forum but enjoy reading topics on here. I need some advice I'm carrying out a job on an industrial estate pulling new supplies to new unit, I am trying to arrange to get the meters fitted all three phase but progress is slow. Could anyone give advise on how I go...
  7. M

    connections

    Is there anywhere in the regs that says you cannot connect solid cores with flexibles, I cannot seem to find anything
  8. M

    Warning labels for electrical earth connections

    Guys just been doing some reading and have raised a question that I am not sure about. I guess you all put your Bs951 clams on the water, oil and gas pipes with the appropriate label but, do you also affix a warning label to the MET if this is accessible. My reading of 514.13.1 suggests that...
  9. P

    Wiring connections required for outdoor PIR light

    Hi all. First post here and I hope someone can help me out please. My existing outdoor PIR light died and I have a new one to fit in its place. The old one not only worked automatically on PIR mode but the 2 way switch which controlled it could be left in either 'auto' mode for PIR or switched...
  10. J

    heating connections

    so I've got an s plan heating system in 3 story house, separate valve and stat for each floor, then the hot water valve and then another valve for underfloor heating in extension. altogether 5 valves. so this wont work on standard 10 way honeywell junction box right? I'm learning these systems...
  11. D

    connections of cpc

    hi, Testing a job at the moment and a couple of DB have all there CPC connected in the trunking instead of the DB. There is a earh bar within the metal trunking but due to the trunking full of cables, unabale to gain access to the CPC. Due poor access to the CPC ive made a report on that but...
  12. 0

    Wireless thermostat for Baxi boiler

    Hi there, Customer wants a new CH clock so replacing a Drayton 5/2 day to a 7 day (LP722) She also wants a wireless thermostat. This is a first for me. I presume due to connections that the RF reciever goes near to the boiler....but are the connections for the reciever made at the boiler or the...
  13. S

    sockets on skirting no backbox

    Hi, Came across some sockets mounted in tall skirting using metal frames screwed to the front of the skirting (trunking adapters?) with no back box. Void behind is hollowed out brick. Pretty sure this is a no no but I can't find the relevant reg, anybody? Cheers s
  14. H

    Alarm door contacts Help!!!!

    Hi I have no experience of alarms, I have just bought an alarm kit for my own house, it is a Honeywell accenta G4 mini panel, anyways I want to wire two door contacts to it, 1 for front and one for back doors, but I haven't got a clue on what connections are required at the contacts as there are...
  15. richardg

    Voltage spikes? Equipment?

    Some help and guidance needed for a property I was called to inspect. After inspecting a domestic property and being paid to rectify all the faults I have been stumped with the problem of recurrent lamp failures! The house has a history of regularly blowing all types and makes of lamps- as part...
  16. E

    Voltage drop detected, various burns in switch and connections in oven flat

    Hi, I am Nicholas, I repair computers from home for a low paying hobby and repair PC power supplies with the skill of replacing bulging capacitors. I will try other repairs using the same skill of desoldering and soldering, and I am living in a single flat here in Auckland NZ. About 9 months...
  17. O

    Dangerous connections

    Hi all, I am not a spark just a reasonably competent diyer. My house suffered a fire and a building company appointed by the insurers have been renovating. Their electrician went in last week to fit faceplates and ceiling roses etc. Today I changed a plastic ceiling rose for a metal fitting...
  18. S

    unusual ceiling rose wiring

    Hi i was just painting my ceiling and unscrewed the ceiling rose to cut in and noticed that the wiring doesn't look quite right. there are 3 cables so i assumed 1 in, 1 out and the switch. There are 3 reds in the centre block, 1 black in the 2 gang block with the neutral of the light, and 2...
  19. F

    power loss @ socket but MCB still on

    Just been to a job where the tenants are saying that a socket in the lounge looses power randomly but does not trip the MCB, it's on a ring so I took all face plates off and checked connections, did IR and got >999 and got continuity on the RFC, 245v and zs 0.39 the problem did not occur while I...
  20. JD6400

    Automatic cow brush motor connections ?

    Hi , i went out to a automatic cow brush that had melted its 1ph motor the other day and after stripping the unit off the wall , due to the size of it we decided that the client would take it in to a re winders local to him as i by the time i had gone back to the yard to fetch one of our plant...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top