Anyone see the K9 kwik-wire connector in this months PE mag? It's like a T shaped clamp and you just clamp it over the flexes and shut it down to create a T joint.It pierces the insulation to connect to the cores.....Unless I'm having a blonde moment though how can you be sure it is connecting...
When's the last time you used a standard connector strip?
With the availability of wagos, Line connectors etc.
This isn't a random question, I do have a purpose behind asking.
Would you consider that this was OK?
On a ring main one leg between two sockets has been cut (red and black T+E) then joined by connector block and a spur has been taken off from the connector block (brown and blue T+E) to run under floor heating (3 amps).
Hi All,
I had a small leak on a copper elbow that I was repairing but when I went to switch the water back on I noticed that a connector with purple wires was hanging loose, its wired at one end to the front panel and has a three hole terminal on the end and its on a wiring loom just under the...
Hi,
I bought in Amazon a speakers for ipod/iphone and when I opened the box I discovered that it has cable with an European plug. I can remove the cable from the speakers but it has been impossible to find something similar with a UK 3 pins plug. I would appreciate any help or link to find this...
Hi people
hoping someone can answer my question on whether or not the following is possible;
i have 3 kitchen lights with the light (switched) lives each going to 3 different switches.
i then have a 3 core and earth wire going between each switch, so basically your standard 2way switching...
R1nutty
Thread
connect
connector
going
help!
intermediate
other
please
switch
switches
As above, 1000 5way push connectors for sale. they come in boxes of 50.
£4 including postage for a box of 50.
same as HELACON PUSH WIRE CONNECTOR 5 WAY (BOX 50) - Helacon Push-In Wire Connectors
cheers,
tim
Hi all,
Would anyone know what this LED wire is called that goes into this?
AURORA LIGHTING LED 6 WAY SERIES JUNCTION BOX ACCESSORYI have bought some LED Aurora au-dled 302 (350mA 1w) for a pelmet in my home. The instructions say for the 240v mains to connect to a constant current driver and...
LINE Products Introduce DIN Rail Terminal Connector Series
LINE is please to announce the launch of its DIN Rail Terminal Connector Series. Although the LINE DIN Rail series is of a higher specification (cage spring) that those offered by others, LINE is offering these to forum members at the...
Hi there, I am doing a system based on Android + IOIO board + Relay for a 230V/16A connector (I am European)
IOIO board only gives 3.3V output (not 5V), so I need a 3.3V relay that works for a 230V/16A connector, is there any relay with this specs?
or
should I need a MOSFET transistor between...
annlee
Thread
android
based
connector
isolator
problem
relay
switch
system
voltage
Hi all
Some advice, thoughts, ideas sought please. Recent install in our house, seperate CU for outside supplies (some SWA feeds to garage, etc), one circuit is a 6A RCBO to run quite a large pond pump, this was tripping the old CU main RCB but that was located to water in the connector for the...
Hi all:17:
Had a correspondence recently with Panasonic stated that if installers replaced original connectors MC3 with any other connectors (MC4 or MC4 compatible) Sanyo now Panasonic CANNOT make an exception and keep the guarantee coverage for the modules which have been modified or have not...
valet
Thread
arial
connectorconnectors
off
original
panasonic
panel
panels
warranty
Hello All
Ive rang up a local electrical wholesales for a MEM Type c 40A 3mA RCBO they sent over a picture of a 40A MCB with a bottom piece to connect in the MCB to make the RCBO. Has anynoe ever used these? normally ive used the Merlin Gerin. The RCBO is to replace a 40A mcb supplying a...
Bought my MI3000 recently and I'm well pleased with it.
Checked my first install recently with it and very pleased with how user-friendly it is.
However, I did note that I had problems doing R1+R2 using the 13A plug lead included with it.
No trouble at all using it to do the insulation...
Thought this deserved its own thread rather than clutter the other one up with stuff...
How do you prepare a cable for insertion to a Wago connector? They type of Wago I mean is one where you just push the cable in - there's no lever.
How would I know how much cable to bare/strip insulation...
my daughter just bought a kitchen from a kitchen company thats closing down.
they included a baumatic BT066ME extractor hood but nothing happens when i turn it on?
theres power going through to the connector blocks then nowhere else,
on the switches are extra terminals but i dont want to move...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc