I am due to carry out an electrical job in a third floor flat.
Incoming supply is TN-S.
Cannot locate a main earthing conductor inside the CU on the earth bar, just the individual circuits CPCs.
There are two earths clamped to the bottom of the metal CU, one disappearing down some metal...
Hi,
I'm getting conflicting stories about this, I wonder if someone could put this to bed once and for all.
I'm replacing a consumer unit in the next few days, and it currently has the common grey tails going from the isolator to the existing consumer unit, one is ,marked "L" then other marked...
hi there I have a plastic consumer unit that was installed about 8 years ago - inside is the standard array with RCD. Im planning to switch to RCBOs (and cost wise I actually bought a fully populated consumer unit as it works out a lot cheaper )
my question is to comply and get through a...
What test should I carry out before changing a consumer unit to ensure that it is eligible for one?
I’m guessing R1 + R2 to make sure it has cpc at circuits. Say for lighting do I check every single light fitting or...?
IR test I’m assuming of course so there are no trips.
I’m not a testing...
Does the consumer units top knockouts need to have stuffing glands installed even if a 50x50 trunking will cover the holes? Or is it sufficient to use a grommet or grommet strip if a rectangular hole is cut?
The stuffing gland will maintain the IP rating but that will be maintained by the...
Smart Meters that can be installed at the Consumer Unit.
For situations where a tenant wants the facility but the landlord doesn't want a a smart meter on their premises.
Does anyone know of such a device?
I'm thinking of something that can be installed outside of the CU monitoring the line...
I am in the habit of fitting 'Fusebox' consumer units. However, I notice that Danson are even cheaper.
Has anyone fitted them? Are they acceptable quality? Any problems with the RCBO's?
If they are 'Chint' like quality then I would rather avoid them. Chint are the only RCD's I have ever come...
What certification do I need when replacing a consumer unit ?
Here are the details.
I am semi retired (electrician) and work for a company as the maintenance man which rents out flats as serviced accommodation, we are currently in the process of having the flats (25 of them) tested (fixed...
Hi guys,
Just a quick one. I’m installing a garage board in, planning on a 6mm SWA supply coming from a 32a MCB. The DB I’m feeding from is a split load board.
My question is, what is the best way to move over the current MCBs to allow me to put in a MCB that’s not on any of the RCDs (as I...
Morning everyone, I have a customer with an old CLICK consumer unit, the MCBs are DB132, DB106, DB116 etc. Does anyone know if the new CLICK elucian range of RCBOs fit this board? I have a picture of the consumer unit (Looks like a bomb has went off) if needed. Appreciate any answers.
Kind regards.
He says 'it's fairly important to change the consumer unit as it wont pass the Inspection in its current state.'
He's coming round tomorrow to replace it, has he given me duff advice?
Cheers,
Matt
Hi Guys
Just setting out final positions for new house we have coming up.
Client would like router in same cupboard as DB, not my first choice really.
If DB is at 1450 from floor level then say we put router/ rack at high level 2300 with a shelf dividing do you reckon this would be ok ?
Other...
Hi. I have a small new build sit to price up. The consumer units are to be sited in the middle of the house behind the front door. After best way to supply from external meter box. I was thinking of using split concentric from kmf with a metal plate over it on internal walls. surface mounting or...
Long time lurker so this may be my first question. I am a qualified electrical engineer, but in aeronautics not domestic installations, and I may therefore ask silly questions. We have purchased a property that is unfinished, and where the electrician went bust before the installation was...
When carrying out an EICR I found this board. The live bus bar cuts across the neutral where the tails have exposed copper. Is this the way these boards come? I have never came across this before
Cheers
Hi Folks
I've been asked to quote for a consumer unit, supply cable and some internal wiring in a shipping container on a private caravan plot (single family residential). The container will be used as a shower block. The mains supply will come from a meterbox installed on a post on the plot...
This is getting embarrassing - I've been looking for a sub-main consumer unit in a church for an hour now.
I've found the incomer. There's a nice old Crabtree board with black breakers, one of which is a 50A for "Hall DB". It's a split level site and the hall is downstairs, and the fat 10mm T+E...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc