Hi, Ive got an upcoming job to determine the cause of a BS88 fuse tripping in a switched fuse unit that powers a 125A consumer unit yet none of the MCB's trip, Just the one cartridge fuse.
What is a concern about this site is that the old fused switch unit is 63A, yet it is feeding a 125A...
The consumer units are in outdoor buildings, each running minimal lights & 2 plug sockets. The cables are all in place, it's literally just replacing four old consumer units with new ones. Tia!
Can a 1-way unit be installed in a meter cupboard? My meter is at the rear of the property and consumer unit at the front.
The meter is due to be changed in a fortnight's time and wondered if i could ask that room is left to accommodate one.
The reason i ask is that i ordered an EV in October...
Hi all. I am due to get an EV wallbox fitted so I will be running a new 6mm SWA from under my stairs to the termination point outside. My issue is I have no spare ways for a 32A breaker in my consumer unit for the installer. Is there any recommendations on shifting some load to free up a way...
Got alot of works being done at my house. I'm debating studding the wall out near the consumer unit in order to easily install new cables. Some of the cables are data as well as electrical and will be enclosed in their own containment.
The board is a metal clad split load board (Crabtree...
Hi folks
Just received a poor image of a consumer unit that requires MCB replacements, does anyone recognise the type and make of the unit or MCBs please, also if the MCBS have been superseded does anyone know what MCB manufacturer/type will fit the unit. Many thanks paul
Client is wanting to remove the wall that his consumer unit is located on.
He has spoken to Western power and they are planning to relocate main incomer to a Electric meter box.
Then will his Electrical supplier will be moving his meter and tails aswell, I am planning to re-locate his fuse...
I have 2 consumer units, one normal and one for t control, I no longer have storage heaters so want to get the meter removed, can I then use the consumer unit to supply the sockets that were originaly used for storage heating, my immersion heater is also connected to this consumer unit so that...
Question.. If a consumer unit needs moving by 1 metre and all the cables need to be jointed through, is a full EIC needed as if its's a consumer unit replacement? Cheers
Not a big one, but it bloody hurt and scared the pants of me! If anyone reading the following knows why this happened I'm all ears.
I safely isolated a garage consumer unit, but didn't turn off the associated MCB in the house, so the tails to the unit were still live, ready to put in a new...
Hi
My consumer unit is located in the garage, the cables are currently clipped to a solid wall above the unit. I am considering putting the cables in trunking to give them some more protection, the trunking would be just under a meter long.
I believe its common practice to use trunking in this...
I don't know if other people are having the same issue with stock as I am, but I do stick to local businesses and they are struggling to keep up with demand during this covid nonsense.
So from time to time I will have to go to a bigger manufacturer.
Because I shop local its what my local...
Been asked to carry out some works in a bathroom. The clients mains board, cutout and meter are in the airing cupboard of the bathroom currently. As part of the plans they are removing the airing cupboard and plan to just put a standard cupboard with a lock around the mains board which will now...
Hi Everyone,
The CU is c.2006 and I was hoping NOT to have to pay for a new metal CU with all new MCBs, RCDs etc. There seems to be a lot of debate about whether my lighting circuit at position 7 requires an RCD but if it does can anyone figure out a way of using the existing CU - the space at...
I’ve just replaced a faulty 63A double pole isolator supplying a feed to a consumer unit several meters away to a flat.
ive come to do the notification on the niceic web page and there is no appropriate category to tick other than
circuit addition or alteration in a special locatiom
install a...
Good morning
I am a consumer, an accidental landlord, which means I rent out my former home as my circumstances changed a few years ago.
I need an EICR in order to carry on renting my flat.
The NICEIC registered electrician that came turned out to be unqualified and the report not worth the...
hi
I have a 4 way consumer unit I need to add to my shed. first there is no busbar , so i have got one from screwfix.
but I am not totally sure where to put the live feed in please?
where do i put the busbar top or bott
where do i put the neutral in / feed
I am OK with most electric
please...
Hi guys. I have an old out building that has been knocked down and in it’s place an extension is being built. The old out building had a ring and a lighting circuit with water heater for a shower all fed From a ccu that came from the main house through 10mm swa. The extension is now going to be...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc