control

  1. D

    Wiring Videx GSM4KC to Ditec E2 gate control board

    I have purchased a GSM4KC to work my currently fob operated E2 controlled gates. On the wiring diagram in the GSM instructions it indicates a volt free contact exiting the unit (figure 26) or 14v (figure 25 if keypad used as standalone) Where should either of these be connected on the E2 in...
  2. J

    Hi there, Fisher and Paykel dishwasher Dw60FC6X1, has a blown resistor on the control module. Can’t recognise the bands!

    Blown resistor, how do I work out what it was to replace it?
  3. A

    Hi guys hope you can help me , i have a large greenhouse , and only one side shuts, control unit? Cheers

    Hi guys hope you can help me, I have a large greenhouse and only one side shuts, control unit? Cheers
  4. Alexander

    Is it possible to : motorcycle EV conversion

    Is it possible, if and why not iff so, To fit an EV motor and controller directly to the stator output of a 125cc motorcycle engine, (pre regulator) Using a fixed throttle set up to increase revs to the required output and to bring it down to the engines normal idle revs for when stationary...
  5. T

    Alarm Control Panel

    Good evening all, I was just wondering if anyone could lend a word of advice/help. I am not very good at DIY unfortunately I am a first time buyer having moved in around 3 weeks ago and today virgin media come to install my internet, however I think he has drilled through the wall close to...
  6. D

    AC to DC motor thyristors speed and direction control

    So i have been given this question: You have also been asked to produce a circuit design that can control the speed and direction of a conveyor with a AC to DC motor thyristor system. What are the the operational features (how it works with speed and direction circuit diagram/s) I am really...
  7. D

    Transistor H-bridge system for a conveyor motor with speed control property's

    Hey, I've been asked a question 'what are operational systems on Transistor H-bridge system for a conveyor motor with speed control property's'. I know that system I've put below would work for a lower voltage application, I just cant seem to find any information on high voltage applications. I...
  8. cliffed

    Ideas on control for lights

    Open office , replacing fluros with led fittings, all have pull switches next to fitting & controlled by remote switch. Pull switches look real naff, obviously there for local control @ desk. Any ideas on better control system,problem is the individual control required needed too.
  9. D

    Draw a start/stop/retain relay control circuit for a 3 phase drill machine

    Hey, I'm just wonder if I can get some feedback on this drawing that I've made? any feedback will be very appreciated thanks in advance.
  10. D

    How to draw an automatic control project

    Hello to everyone. I made a circuit, but I do not know how to draw a project for it. (German Norm) or (American norm) Relay = R1 I entered the A1 terminal of the sensor cable from I24. (+ 24V.) I entered the A2 terminal of the sensor cable from C24. (0 V). I entered the cable from OSSD1 to the...
  11. N

    Standy generator control panel issues

    Control panel attached to the standby diesel generator gets frequently damage despite of earthing of the body and separate grounding of the generator.What might be the causes to damage the control panel of the generator frequently during lightning sound and light rain condition? only backup...
  12. L

    2 Gang Light Switch Dual Control

    Hi All, I've searched a number of threads and can't seem to locate one that works for my situation. There are two lights controlled by two, two-gang switches. One switch is at the top of the stairs and the other at the top, so are the lights in question. They've not worked correctly when I...
  13. R

    Control Transformer Question

    Hello everyone... I am installing a 12vdc tachometer on a industrial mixer. There is 480v 3ph motor starter with disconnect box near the machine with a 480v to 120v control power transformer in it. I was going to wire a typical plug in style 12vdc power supply to this 120v supply, but it didn't...
  14. R

    How to shut off 120v baseboard heater?

    I've planned a 20A circuit serving a tiny half-bath in a workshop. The circuit will contain a few LED ceiling lights, a receptacle (not for tools) and a 350 or 400W 120V baseboard heater. So it would not be convenient to shut off the heater via the main panel. When I'm not working during the...
  15. N

    New Touch Control Hob Problem

    I've just purchased a new touch control hob as my old unit eventually gave up the ghost. I wired it directly into the cooker circuit just as the old one was but it refused to turn on. Nothing, not a peep. So i took it back to the retailer who, without a quibble replaced it. I wired this the same...
  16. 9

    Can elec UFH thermo control floor and elec radiator ??

    Hi all, new member here with a technical question. I am doing a refurb and want to know if I can connect a 300w electric radiator to the electric UFH thermostat. Basically want the radiator to come on at the same time as UFH. Thermostat will be running in floor sensing mode and controlling...
  17. udud22

    3 Phase Control Relay

    Hi, I am new to HV Electrical Stuff. I am trying to use a emergency stop button to kill power to BOX A remotely. The wall socket has 3 phase 380V supply without neutral. I want to introduce a control relay between BOX A and Wall socket. The remotely operated cable (20 metres) with Emergency...
  18. C

    Connecting a Brake Light Module to control all 3 brake lights

    Hello, I need detailed assistance badly. I am trying to connect a Brake Light Module or a "Flasher" to my brake lights for attention but I want to control all 3 lights when brake is applied, rather than just the 3rd brake light or the main brake lights. The instruction for the product looks...
  19. J

    Wiring a 4-Function, 3-Switch Wall Control

    Before you write go get an electrician - I HAVE! And he's never wired one before. AND asked ME to do some research!! Before you also say get a new one - though boy do I want one - it is a long story and not an option. The switch is to control a bathroom vent fan with an inbuilt light...
  20. P

    Gate control and intercom - fuse blown but why?

    I have just purchased a new video intercom system which consists of an outdoor unit with key pad, camera and RFID access and then a 7 inch internal monitor. The monitor is connected with a 12v transformer plugged into the wall and then an RJ45 Ethernet cable running back into my home network...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Green 2 Go Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses Heating 2 Go
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

Daily, weekly or monthly email

Advert

Back
Top