hi guys, just wired up a Honeywell evo crontroller with a relay for the heating, a tank stat and a relay for the hot water, I managed to get it working after a lot of messing around, the problem is it's a megaflow hot water tank and I have disconnected the megaflow tank stat which has a overheat...
Ok, so I've been asked to check a possibly faulty lower immersion element. Sure enough, it's gubbed. Fortunately I had a spare the correct size in the van. Drain down a massive cylinder, but can't get the element shifted. Not insured for hot works, so ask the letting agents to organise a...
Hey all, so I'm rewiring a nightmare house while girl still living in it ! Plumber gets a cylinder and says direct 1 X 3kW standard immersion. So I run a 2.5 through most of house to loft.. Comes today saying just worked out he got wrong cylinder and where he wants it there is no space for vert...
Hello all!
I'm a plumber and have a customer where the s plan is working fine for both zones (ground floor, 1st floor + cylinder) but not firing the boiler when hot water demand from the cylinder is operated. 2 port valve opens and pump runs but boiler shows no demand for heat. Any ideas why...
Hi all,
i I have my first combi to wore up next week. I have got the drawing here for the controller and it gives me terminals for a hot water cylinde stat,The system has no cylinder in it s it's a combi so I assume that somewhere in the boiler it has a built in stat? Like I said this is my...
Hi i need some advice on how to wire my codice 542794 stats to my boiler
i have a buffer tank and like to put a stat top and bottom of cylinder ,i have a connection from my boiler for a thermostat with a switch live and perm live and neutral
i need to no were they go in the stat inside stat...
OK, so I'm not a plumber but have a fairly good idea how this system works. I'm not alone with this problem either, there has been a similar post but it's old and doesn't have a resolution - though they have a temporary fix that doesn't work for me...
Boiler: Baxi Solo 15HE
Controller: BG UP2...
phatado
Thread
british
british gas
central
central heating
controller
cylinder
don't
gas
heating
hot water
position
valve
water
when
Hi,
can anyone advise...
i would like to ideally use Honeywell.
i want the stats and programmer to be wireless.
it needs a frost stat
it also needs two stats and a programmer
and it needs three channels / zones
any ideas on how to achieve this?
I have no experience in the installation or fault finding of, central heating systems.
I don't do, and have rarely done, domestic work.
I volunteered recently to look at an elderly lady's situation whereby the system had been installed, then altered as the room stat was relocated from the...
have noticed for a while now that the hot water cylinder stat might not be working correctly. Hot water is timed for morning and evening only however as it only comes on for a few hours i just put it down to it not heating up fully, stat is on 55c.
Now this morning, i switched on the immersion...
Hi all
Just a quick question. Following the installation of a replacement hot water cylinder in a tenanted property. The tenant is demanding an Electrical Installation Certificate a Periodic Inspection Report & an entry on the Electrical Equipment Register So wanted to know if the members would...
Sanke
Thread
asked
cylinder
electrical
hot water
installation
question
replacement
water
Was looking for some advise. Plumber has installed water tank with three 4kw elements at the moment I have ran three individual circuits. At the moment the salon is running of the boiler. I am just looking if anyone would know what 7 day time clock would be suitable for 4kw. Want the contractor...
Hi,
My heating system is a myson apollo 30b with a 3 way valve etc.
The other day wife said was a popping noise coming from kitchen where the programmer and boiler is , on investigation i have found when you turn down the tank stat which is a drayton hts 3 it when it gets below the temp and...
klunk1971
Thread
boiler
cylinder
heating
rcd
seems
sometimes
trip
valve
Hi guys
What is the purpose of the third connection at a cylinder stat which appears to connect to the central heating pump on most wiring diagrams I have seen?
The system I have is what I assume to be gravity hot water with pumped central heating .
There are no motorised valves, just...
Evening all,
A job I am on as an aside the customer asked me to have a look at the heating/hot water system as the hot water is not heating up. It is an unvented system with vaillant boiler and combistore cylinder.
Anyway I tested up to the tank stat/cylinder control and found power up to it...
Hi all
been called out to a boiler replacement with the above boiler. The problem is it wont run on heating only. have check wiring and all I can spot is that from controller there is no wire going from HW OFF to cylinder stat terminal 2 and grey on valve. Any thoughts and no spare cores in...
Hi, i have changed my hot water cylinder for a Megaflow hot water cylinder. now having problems to wire this thing in. the programmer i have (Tempus 7) has only got HTG on and DHW on options, so i it's only for 2x2 port valve system?!?! originally i have only 3 port valve at the moment, looking...
http://www.solartwin.com/wp-content/uploads/2011/08/Combi-prefeed-NONmodulating-giff.gif
http://www.solartwin.com/solartwin-features/basic/plumbing-in-solar-thermal-to-a-combi-boiler-combination-boiler-geyser
Hi all imhaving a 4kw solar pv system with an immersion controller(i dont have an...
Joe Markey
Thread
combi
cylinder
hot water
new
options
solar
solar pv
water
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc