Disconnect once check twice..(or more)
Found HERE at Trading Standards
Risk level
Serious
Risk type
Electric shock
Risk description
The fault was identified during routine installation process which includes a test. It was found that the switch did not isolate the circuit. The product does...
Two wires have disconnected when I moved a double switch for painting. Any ideas where they go please? I guess the live at the top goes into the com but no idea where the live at the bottom should be connected. I’m a complete novice so don’t want to do something that may be dangerous!
Hi,
Would like some advice please on the following issue.
2 (dimmable)wall lights which are plugged into a mains socket via a 5 amp fused plug. At the present time the two lamps are switched on and off by the plug socket. They are wired as follows. Lamp 1 is connected to the mains, and Lamp 2...
Hey all,
Could I get help with wiring this double switch which will be individually switching front and back external lights.
With this switch I have a live source from consumer unit going in, and 2 separate cables going in for front and back lights.
so when I connect live in from consumer...
Hi
Could someone advise.
I was thinking about installing a plastic tall lamp post in my garden. Its double insulated, ran through a channel in the ground to an external wall RCD.
I was thinking armoured cable to run, channel would be approx 13 feet.
Could the cable be wired to a junction...
Hi,
I am looking for some advice on the best way to install 5 double plug sockets into my garage, all of which will be running multiple computers.
My CU is located in the garage.
Would it be best to install the sockets onto their own ring main, or to add them onto the existing garage circuit...
Hi,
Just purchased a new wall light and it has no earth on terminal junction. Instructions say ‘double insulated - no earth required’.
Here is a picture:
How would this protect you if the wire from wall broke loose from this junction box and touched the casing which is metal? Or is it...
Afternoon
Ive just finished PV course and have a question about DC cabling being installed through a house, from the roof to the inverter within the garage below
im struggling to get an answer that isn't Conduit or metal trunking, however my question is, if the DC conductors where to be...
I have a 4mm2 armored cable going from the CU in the house, under the drive and into the garage. The breaker for this is a 16 amp type B. I want to have 2.2KW planer machine in the garage that has a 16 amp plug whilst also keeping three existing double sockets in the garage. The three double...
I am an ozev approved installer and have installed a couple of single home wall charger units but have a requirement for two outlets at a parking spot with a b&b, for staying guests; has anyone any experience of a multi-outlet system or can recommend which units to go for? or would two singles...
Hi all.
I want to add a double socket, the closest one is on opposite wall.
So instead of using 2.5 T&E and then pvc trunking, can I use 2.5mm white flex?
Only asking as flex would look a little neater clipped around the bottom of the skirting.
Weren't sure what if coming from.one socket...
Hi All
I am new to this forum. Hope you are all well during these tough times.
I need some help regarding the modification to electrical wiring in my house. Please see a pic of the existing DB.
I removed the old electrical oven and installed a new one 2.99kW on the opposite wall. It will be...
Hi,
I have recently purchased a new kitchen including applicances (which I am waiting to be delivered). I am looking to sort out my electrics and get the sockets and fuses in the right place.
Is there any reason why I can't plug the fridge/freezer and gas hob to same double socket?
The...
Hi,
I have a double electric socket, standard 13amp. My son broke a plug in one of the sockets so I decided to change it.
The new one I purchased had 2 connections for the earth wire whereas my old one only had 1. I read that it's ok to only use one of the connections so I did. Once...
Greetings,
First post here. Would be most grateful for any expertise available on this issue. I am trying to convert 2L fixtures to LEDs. They each have (1) F13 T5 and (1) F8 T5 end on end. I ordered Type B (ballast bypass) LED replacements thinking I'd bypass the ballasts, install the...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc