I have an immersion heater controlled by an horstmann economy 7 Quartz timeswitch that will not heat the tank. The whole heater unit was replaced only a few weeks ago, and I replaced the timeswitch like for like in january last year and the thermostat had already been replaced 3 times in the...
Hello fellas
Been asked by a letting agent to go and find out a problem on an imersion heater? She is telling me If they leave the immersion on for a couple of days its trips?
Couple of question for you guys
1/ To tested the immersion heater element carry out a...
Well looking for help again.Got asked to have a look at an immersion heater that trips the rcd as soon as it reaches set temp.This can be set at 50 degrees to 90 but as soon as it gets to the temp off goes the rcd.Have cheaked ir on cables back to board no problems,restance of dual elements 1...
Hi, I've been asked to go look at an immersion heater which isn't working.
I haven't looked at one before and would appreciate a heads up.
Obviously there may be a problem with the power supply or the unit may be faulty.
Would appreciate any comments by those with experience as to a suitable...
Hi , looked at an oven this afternoon that had tripped its mcb 40A, on 10mm T&E, and on resetting it the oven did not work. However, fan and grill both still worked. Tested continuity across L and N at isolator - greater than 199 ohms with oven switched off and 127 ohms with dials turned on...
Hi all, I am 2nd fixing a job that someone else 1st fixed. I hav two wire coming out from under the tiles. One is a two core. One brown and one blue. The other is a bit bigger diameter cable and one core is blue and one is grey. As i did not install it i dont know which is the sensor and which...
Hi folks.
Changed a Cu today. No rcd protection, Changed for a split way board. All tests were fine. Came to do Zs test on immersion heater - everything fine. Turned on DP switch to immersion and rcd tripped.
Had a good look at all cables for the circuit and all seemed fine. Disconnected...
Hi all,
Finally got around to installing UFH (loose cable type)
40sq metres being laid in a kitchen using 4 kits (10sqm each)
main heating source, 2000w per cable, Underfloor thermal board used on timber floor,
I was just wondering what amp size contactor to use to connect x4 cable to...
hi
Just out of interest. Suppose a customer has an electric cooker like this one say.
The manufacturer doesn't say, The cooker is rated at x kW? (could be 12kW say for a cooker)
They give me the following information:
Main oven energy consumption 0.90kWH.
Top oven energy consumption...
Hi, wonder if anyone can help?
I have an old electric cooker on an RCBO cooker circuit, and one of the rings trips the RCBO when you turn it on, does this mean the element needs replacing?
Hi,
I desperatley need to sit the C&G 2392-102 practical (exam) at a college or training provider centre as an external candidate. I have passed the 2392-101 (exam element)and hold the C&G 2382-100.
I need the practical element to gain the full qualification to carry out some work.
Does...
Good evening lads,
Ive not had a lot of experience with immersion heaters but ive got to look at a faulty one sometime this week. The water is heating but the customer is only getting half a bath full. Would it be possible for the immersion heater to have to elements and the upper one is...
hi, has anyone ever come across an immersion heater where the white pre fitted cable would be the neutral? im pretty sure the said piece of cable would go to the stat with the feed (brown L) going to the other side??? the reason i ask is ive just asked to a neighbours home where she has a e7...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc