WIRING FOR WALL SMART SWITCH FOR CEILING FAN/LIGHT
Just bought a smart wall switch for a ceiling fan/light currently connected to a single switch, fan has pull chains. Pretty sure I know the wires connected to the wall switch, not my first rodeo, but just want to make sure so I don’t blow the...
Hi, have an old bathroom fan. Which has two wires the black and red (line and neutral).
The fan has no isolator switch and was powered when the bathroom light came on. When turning the light off, the bathroom fan stopped.
I disconnected the fan wiring from the ceiling rose to clean the fan. Now...
Hi all,
Got an awkward bathroom fan installation in a downstairs flat, concrete ceilings and (some) walls. Bathroom is already fully tiled and 'finished'. Due to the window in the bathroom, it is impossible to get a fan directly out of the one external wall. A window fan is a theoretical option...
Hi All,
Thank you for your previous advice - it resulted in us replacing our precious Smeg range with a Hotpoint; however we now have a new issue that I was hoping you might be able to advise on:
The oven works nicely and the heat seems good etc. But it makes a pulsing noise when you're using...
Hi
I'm looking for some advice for adding a time delay on my parent's shower room fan.
My parents had a section of their garage converted into a shower room with toilet. But the builders did something a bit odd. They fitted a pull cord light switch by the door and then a separate pull switch...
Hi
Customer has an extractor fan that’s inside the shower cubicle high up on the wall. The extractor fan has no form of isolation and is wired into the socket circuit not the lighting circuit (I have never seen this set up before) and hasn’t been fused down. So because of the way the extractor...
Is there such a thing?
Just a standard bathroom, but can’t get through a wall or take out a window.
Are there specific condenser fans, or just use a normal one and fit a normal condensation trap and block up the end of the duct?
So today I was coring a 6 inch hole for a kitchen fan, now I cut my hole in the kitchen plasterboard and used a long sds bit to drill out the way, then I cored my 6 inch hole back the way. The hole coming back in is slightly off, am I best coring from inside back out until the first bricks...
HI There,
I would be grateful if you could help me, I have a very long duct between the bathroom and extractor outlet vent and for sometime, the bathroom stream overwhelms the extractor fan so much that I end up having severe condensation and moisture puddles, because it was a new build. They...
I've installed a replacement bathroom extractor fan. Pic on the left is the old one. Pic on right is the new one. Wired the same way but the fan won't work when the bathroom lights are switched on. But if I put a multi meter on the Switched Live & Live terminals, it starts working. Is the fan...
Explore our weekend ventilation offers, featuring some great savings on 4" fans, Positive Input Ventilation Units and a shower fan kit!
Hurry as these deals end at midnight on Sunday!
To visit our weekend offers click here!
Hello, I currently have two switches in my bathroom. One controls the lights above the sink and the other controls a light above the toilet and also a fan. I want to separate the switch from the fan and have that separate. I got a nutone fan that has a wireless remote, so I don't need wires to...
I'm sorry if this isn't in the right place but this is my first time using this forum.
I'm also sorry if i make some mistakes but I'm new to this kind of electricity and English isn't my native language. I bought a "new" power amplifier for my audio setup and the fan in it is very loud. I would...
I bought a ceiling fan with LED lights.
After some time the led lights started flashing when I put them on. Now it does not even jump up anymore, only jumps up very weakly or flickers very loudly.
The fan function works fine though.
How can I fix this?
hello all, pardon my ignorance in not employing an electrician, however, im a diy'er whos changing the light switches in my house and came across this unusual wiring for my downstairs loo. its a single light which has a fan which can be isolated as necessary. I ordered all the new chrome light...
Hi i have these 3 red leds come on the extractor fan and it stopped working. Anyone knows how this can be resolved. Will a clean only suffice or this needs to be replaced?
i have a toilet compartment and a separate adjacent shower room and i am fitting one remote extract fan, via a Y splitter to ventilate both rooms. But, ideally i would like 2 way switching within each room (the shower room would need to be a pull cord) but with a neon or other indicator on the...
Good afternoon everyone.
I have fitted an extractor fan in my bathroom with an overrun timer, to start when the bathroom led lights are turned on. I have wired the feed to the fan via an adjustable overrun timer and DP isolator with the SL for the fan timer coming from the light switch.
The...
Hi All,
Weird matter happening here and I hope you can help!
My 3 Pahse EC Fan is connected to a sensor and a controller for the temperature setpoint. A control panel to manage the EC Fan is in the room. EC Fan above faux ceiling. The panel has it's own MCB. The RCD is upstream, before the...
I got my hands on an old floor standing fan and started looking to rewire it.
I found this part, I think it's a resistor, but was hoping someone could confirm for me, and maybe suggest a replacement, this thing is kind of crusty, looks like it was covered with layers of something in the past...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc