filling

  1. N

    Question regarding filling the Condition Report Inspection Schedule. Please Help.

    I have a question regarding filling the Condition Report Inspection Schedule For Domestic Up To 100 A Supply. My question is when carrying out the inspection on my examination test board there is a shower Unit with its circuits but no shower cubical and there is no bathroom or bath basin or a...
  2. N

    Help filling the new New Condition Report Inspection Schedule For Domestic.

    Hi My exam on fault finding is near. I now have to fill in the new report (Condition Report Inspection Schedule For Domestic And Premisses With Up to 100 A Supply). The report consist of 7 sections. Section 1 is Distributors Supply intake equipment, Section 2 is presence of adequate...
  3. N

    A question regarding filling the Electrical installation Certificate.

    If I was the inspector When filling the Electrical installation Certificate under Declaration For Inspection and testing, I only need to sign this part? Also what do i put in the space for amended to ..?....(date) except for the departures, if any detailed as follows. What date goes in that...
  4. Y

    A couple of basic test sheet filling question

    Hi all, Tommorow I have an inspection and testing practicle, Fairly confident in the actual testing part however just a couple of questions for filling in our test sheets 1) Am I correct in thinking you dont need to record a type for an RCD? 2) What should be recorded in the I^N (Braking...
  5. S

    Form filling primary over current protective device

    On the main over current protective device I'm looking at it states 100 amp 1.3/16 DIA does anyone no what type and Bsen num it is as I can't see it in the regs. Thanks Chris
    • schoe
    • Thread
    • current device filling primary protective
    • Replies: 1
    • Forum: UK Electrical Forum
  6. S

    Advice required on form filling

    Hi there I am going to replace a outside light. The circuit is fed from a sfcu spurred from ring socket circuit. Do I need to check the end to ends and figure 8 checks on the ring, or is r1+r2 and insulation tests and other standard tests for spur and light point satisfactory. Also for another...
  7. G

    chasing in oval conduits and filling in chases advice please

    Hi guys, before starting this thread I have searched old threads on this site and had no luck finding a good one. I started a thread a few weeks a go my house rewire and now im after a bit of advice on filling chases. I rarely do domestic electrical work so have barely touched on chasing, the...
    • Guest112
    • Thread
    • advice aus before bonding chasing conduit filling please
    • Replies: 30
    • Forum: Australia
  8. S

    form filling question

    Hi all im filling out my test paper work getting everything ready for my first inspection and i just have a question regarding one of the sections on the electrical installation cert. In the section Main switch or circuit breaker does this apply to my main switch in the consumer unit ie 100a 2...
  9. R

    Help with filling out NIC certs please?

    Hi guys, as some of you might know I`m new to the NIC DI scheme and new to filling out these purple certs. Q1. On the EIC purple certs, under the "SUPPLY CHARACTERISTICS" section, it asks for the external earth fault loop impedance by enquiry. Does anyone actually enquire or what reading should...
  10. V

    filling in fit form Scottish power

    Hi can anyone tell me who is the [ name of authorised signatory ] on a Scottish power fit application form. Is it me or do I get the installer to sign this. I am trying to fill out most of the form today, before my install tomorrow.
  11. D

    pv installation inspection form filling testing query

    Hello, Ive installed an additional rail in a (huge) consumer, tailing off the main 30ma rcd switch (source side) into a 60947-3 isolator, feeding a 60898 16 onto my inverter cct. do i treat the additional rail as its own installation (like an additional consumer) or do i have to get involved in...
  12. S

    filling out certificates

    hi, i have been filling out some practice certificates at work today and have some questions before i go for training. i was looking at a BS1361 main fuse, how can you tell if it is type 1 or 2...it wasnt written on it. what is the normal time recommended to put on a certificate of when a new...
  13. Goody

    Filling in an EIC.

    Hi, I am just filling an EIC and I have no difficulty filling in the details for the “Final Circuits” but how do I fill in the details of “Distribution Circuit”? The circuit in question is for the garage; the SWA cable from main DB terminates on to a mini DB in the garage and the garage has 2...
  14. T

    filling out certificate

    Filling out the above for a Sub board (D.B 12) TN-S TP&N There is no board fed from abnother board, there all split in henleys straight from the meter. D.B 12 is single phase. Im getting Zs of circuit 1 as 0.22 R1+R2 as 0.06 Previous PIR's show Ze as 0.22 but how can this be if a...
  15. B

    Best form filling eca software

    Can any one tell me the best eca form filling software out there and if they are using it. Thanks in advance
    • Bsharp
    • Thread
    • aus best eca filling software
    • Replies: 1
    • Forum: Australia
  16. N

    Filling Stations (Hazardous Areas)

    Hi everyone I have been asked to look at the sign lights not working on the forecourt of a petrol filling station (flourescant lamps for price on pole). Apparently not working since recent PIR carried out by specialist company. Do you need any special qualifications as this is a filling...
  17. M

    campsite pir form filling

    Having a blond moment. Do i treat it as a tt sub main to each point and do a form for each point and one form for the main supply panel.
  18. K

    Filling in the G83 Forms

    I need some help with filling in 2 questions on the G83 form ...doh Maximum peak short circuit current (A) ? Type of prime mover and fuel source ?
  19. R

    L.P.G filling station

    Does the lighting within an LPG filling station area have to be of a certain type? I have been told explosion proof but this sounds stupid to me as if there was an explosion in the area, lighting doesn't really matter. This is to be located next to an outside LPG pump for fillg fork lift...
    • reynard116
    • Thread
    • aus filling station
    • Replies: 21
    • Forum: Australia
  20. B

    bit of help please on filling in cert!

    on a domestic electrical installation certificate that i was looking at filled in by a contractor where it says characteristics of primary supply i wondered what the following meant? BSEN 1361 is this a BS88 fuse? under the box - type - it looked like he had filled in the number 1 - what does...
Best EV Chargers
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.
UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
JBOD Forums: a forum for JBOD storage server advice
JBOD Suppliers: JBOD Storage Server Supplies
Back
Top