hager | Page 2

hager

Recent contents View information Top users
  1. P

    Hager meter kit fusing stupidity

    Today we got our Hager meter kit for one of their 125A TPN boards. It has a little DIN rail fuse holder as the meter is powered right off the incoming isolator/RCD/etc without any MCB for protection (so the meter can't be switched off without everything going off, presumably so you don't cheat...
  2. P

    Industrial TPN board, Hager or Wylex?

    As currently got sod-all to do, I was thinking about the choice of TPN board for a new set up. It only needs 2-3 three phase circuits and around a dozen single phase, total well below 100A, so initially our sparky had suggested something like the Wylex NHTN12MR 12-way board as ample and his...
  3. J

    Hager Consumer Unit - Fire retardant grommets?

    When working on Wylex consumer units I always opted to use semi-blind fire retardant grommets. (British General Fire Retardant Semi-Blind Grommets 13 Pcs - https://www.screwfix.com/p/british-general-fire-retardant-semi-blind-grommets-13-pcs/9638p) These ensure that any internal fire is starved...
  4. 1Justin

    Hager part KRN190 neutral connecting block

    Who's familiar with Hager KRN190? It's called a "neutral connecting block" by Hager with no further info. This seems a maybe misnomer, but I have never seen one in the flesh.. I'm assuming it would have a lower terminal spaced to fit a standard Hager busbar prong if it were fitted like an MCB...
  5. T

    Price of Hager RCBO's

    Does anyone know what a good competitive price I should be paying for the above?
  6. D

    Hager Din Rail Mounted Time Switch

    Has anyone fitted these into an Invicta 3 Type B board? Wholesaler asked Hager whom stated they need to go into a separate enclosure, but couldn't elaborate on why. My preference is to mount them in the DB under the corresponding RCBOs and I cannot see from the spec sheet and photo why this...
  7. V

    hager invicta 3 - rcd incomer neutral

    hi about to install a invicta 3 , hager 3 phase board. the neutral on the board is on the left, yet the 4 pole time delay rcd i am going to use has the N labelled on the right hand side of the RCD, so with the copper incoming kit links it won't fit? are there Hager version rcds with neutral on...
  8. spud1

    Why are the two poles of the Hager SPD rated differently

    So I was installing a new split load Hager DB (with the integral SPD) and noticed that the SPD cartridges connected across the neutral and line poles of the SPD were rated differently. Is there a reason for these different ratings? Spud
  9. happysteve

    Oh Hager, you little beauty...

    First time using Hager ADA reduced height RCBOs (as opposed to their tall ADN range). See how beautifully they match up with their MTN circuit breakers (circuit far right next to main switch, for SWA feed to shed). :D Compare to BG, my "go to" budget (and garage DB) brand... can't even get...
  10. SJD

    Hager Duplex Cu and KRN190 Neutral connector

    I have a Hager Duplex (stacked 2-row) CU to install. The main switch is on the bottom row. There are cables from the switch feeding the top row. Both cables are fed via a KRN190 "100A neutral connector". The neutral enters the top, and from the bottom is fed to the N busbar. Now I can see this...
  11. ferg

    Hager dimmer module swap

    Does anyone know if I can swap out the module on a Hager rotary dimmer switch for a different module i.e the aurora dimming module? I'm looking for a hager solution for dimming Enlite E8's Thanks in advance
  12. Leesparkykent

    Hager square knock outs.

    Just seen this on twitter.
  13. D

    Hager boards. Cant stand them

    Had to replace an MCB on an existing Hager board (dual RCD) as part of yesterday afternoons job. Having to drop the entire busbar just to change one MCB, and then fiddling around in a tight space to get it back, then the paranoia over whether I've missed a clamp. Mirror, torch...still cant...
  14. J

    Using Hager J804 to wire two lights controlled by one switch

    Hi, I’m replacing the two lights in my living room (both ceiling rose pendants) with flush fit lights, so was looking at using the Hager J804 junction box (I have access under the floor above light fittings). Both lights are operate by a single switch. The ceiling rose has no Loop out. My...
  15. Gavin John Hyde

    Functional earth fly leads and rcbos

    Whats peoples approach when dealing with the earth fly leads on RCBOs? Got a board to fit next week and the bits arrived today. So been busy getting rid of packaging and putting bits together ready and checking its all arrived. Hager say you can trim the fly lead and nuetrals down if needed as...
  16. Malcolm

    Hager RCBO to fit old board

    Hi all Would anyone know if a new Hager RCBO would fit into one of these old Hager boards? I have to do a small amount of work and there is no RCD protection. Thanks Malc
  17. NDG Elecs

    Hager RCBO compatibility

    Hi Lads n Lasses. Just been to look at a job, just small stuff. One thing was that they wanted a new shower putting in. I was going to check the busbar depth (from front/back of OCPD) on the CU but got sidetracked by bad jokes chit chat with the owner! So never checked the CU thoroughly. I...
  18. M

    Din rail connectors - Best place to purchase? & Hager Invicta

    Hi all, I'm wondering where people purchase their din rail terminal connectors from for extending consumer unit cables? Also, has anybody had any experience with the hager invicta for commercial premises and if so, what did you think of it? Thanks, Mike
  19. GMES

    Hager contactor guide

    GMES submitted a new resource: Hager contactor guide - A guide for contactor choices Read more about this resource...
  20. G

    Surge Protection Device question

    I am busy doing some work with a local contractor to get some up to date hands on experience. whilst doing a EICR today i come across a CU with SPD in. The property is a recently built 5th floor flat about to be let on a new tenancy and meets the criteria for requiring a SPD. The whole set up is...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top