installing | Page 10

installing

Recent contents View information Top users
  1. B

    Rcd trips after installing rcd

    Dear all, Really shattered today. It is old house. Fusebox vey old type. I replaced it with a new consumer with rcd. However rcd keeps tripping for all the sockets circuits. Upstairs lights fine. Downstairs generall fine but rcd tripps when I turn on kitchen lights. I disconnect earth for all...
  2. O

    Installing digital thermostat

    Hey fellas, I've bought a digital thermostat to replace and old manual honeywell that's in a bit of a bad way. I've open both up to check the wiring but the new digital doesnt have an earth. I don't want to start messing with them until I'm sure where it should be placed. I've attached some...
  3. M

    Electrician Jobs Bathroom lights and fan need installing in Surrey for a plumbing firm

    Hi Guys, I am looking for an electrician in the ealing area as mine has retired. I am installing a bathroom and I am putting in a false ceiling where I would like 5 led downlights installed as well as a quiet fan, isolator and so on. If you would like to discuss with me please contact me. Thanks
  4. gazdkw82

    installing shower-main fuse

    my sister has asked if i will install a shower for her when i have sufficient knowledge and experience. iv been going through some figures as a little practice whilst im not very busy. This is the CU set up TNCS supply ------------CCU------------ downstairs sockets - 32A - 32A with diversity...
  5. T

    E.I.C Installation report checklist

    Hi all A little clarification please if anyone can help. I work for a metering company installing modbus and AMR tenant sub metering and data logging equipment. when installing a new supply (1new circuit) from an existing DB for whatever purpose, we are filling out a full E.I.C cert if an...
  6. reddwarf4ever

    installing 1.5 armoured cable, need termination advice please

    I am replacing a 1.5 internal cable that was run temporarily to give a constant on feed to,my new boiler, as the previous one didn't require this. Unfortunately the only route this could take was from a bedroom ceiling through the floor to the boiler downstairs. I intend running a 1.5 armoured...
  7. M

    Installing brick lights for the first time

    alright guys im installing 9 brick lights outside ran 1.5mm armored to each point just picking fittings now any recommendations and tips on installing them
  8. J

    Installing washing machine and t/drier in room with wc and basin - is it allowed.

    Hi Folks First posting. My background is in joinery with any little knowledge on electricity picked up as I went along which isn't enough to answer my query. The lad lives in a flat in a large block about 150 years old. In the flat is a room about 6 feet x 5 feet containing a wc and wash...
  9. E

    Installing electric Hob in mobile home with 40A intake

    Hi, someone wants an electric hob of rating 6Kw fitted in a static home thats feed by a 40a MCB there is one 32a ring final, two 6a lighting and one 16a oven circuit, after applying diversity the installation is already over its maximum demand a little without adding the hob. It is unlikely...
  10. D

    Installing 3 Phase supply to new 5/6 Bed house

    Been asked by a customer to quote for a 3 phase 100amp supply to his new build 5/6 bedroom house. His meter by the front gates 135-150m from house. Cable will be buried in ducts, i've done some working out myself (long time since i've had to do this). Using a 70 degree thermosetting cable its...
  11. N

    Wall Chasing Machine for installing electrical wiring?

    hi there im thinking of getting some sort of chasing machine i already have a dust extractor anyone recommend one. just for odd chases is it worth it . i was thinking of a makita cordless grinder i know i couldnt use the extractor on that but whats the dust like when cutting out boxes and chases...
  12. S

    Looking for some tips on installing charge points for electric cars

    I am looking to start installing charge points at domestic dwellings. Was just wondering if yous could give me a bit more info on these as regards to regs etc.
  13. L

    Installing PV non MCS

    Hope somebody can help I am a time served sparks and a PV installer with all the relevant qualification. I have installed around 250 PV systems and signed them off as I m NICEIC registered. The MCS was dealt with through the companies I was installing for. So here is the question- As the...
  14. C

    Confusion After Installing New Bathroom Extractor

    Hi Guys I am in need of some help. i have just installed a new bathroom extractor. Since the installation, the following happens: isolator in off position turns the light on and off as usual - extractor fan not working as expected isolator turned on, causes the bathroom light to turn on and...
  15. B

    Camper Van conversion - Seeking Advice before installing electrics

    Prefix - I've tried to post this in automotive, but it would not let me. This may be because I have not been recently active. Apologies if this is the wrong platform for this post. Firstly- my apologies if I have posted this in the wrong section - I am nota qualified or trainee electrician. I...
  16. A

    Installing a LightwaverRF Dimmer

    I'm DIY installing a 1 gang LightwaveRF dimmer. I currently have a Tenby switch (which I think is 2-way, but only actively 1-way). As per the installation guide (http://lightwaverf.com/wp-content/uploads/2015/10/JSJSLW200.pdf) I need a Switched LiveWire Out Live Wire In Which wires...
  17. N

    installing socket in shed

    Hi, I'm currently on a level 2 C&G course at college with a bit of experience. I have to install a socket outside in the shed in my own house. I have a few questions i'm not too sure about: 1. is SWA cable the only one to use for taking power to shed or can I use T&E run in conduit? Is...
  18. bartkusal

    What tests and paperwork?

    Hi, haven't been here for a while.:waving: Just a quick one, what tests and certificates needed, if installing a couple of circuits, 2A loads from the control panel in the plant room, it will be supplying boilers Don't say its a full wack EIC , and if I am concerned only with circuits I am...
  19. A

    Installing PIR sensor with room light

    I'm trying to for a PIR with a light but unsure how to connect. I have good knowledge and can install plugs etc have installed lights before. The pir has a NAL connection. What goes into A? And how would I install a light? Based in UK.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top