I was just reading the Building regs (as you do when you are a very sad person:drunk:)
and there is a difference in the definition of special location for bathrooms; the building regs state it is within the zones in BS7671, and approved document P states that it is the entire room.
This may...
I looked at a job today to add a new shower circuit. The c.u is close to the gas meter, less than the 150mm recommended. It is not going to be possible to move it as the customer won't pay the cost. Seeing as im altering an existing circuit not changing the c.u does anyone know if I have to...
Hey guys I was hoping you guys could clear some issue up for me ive been asked to snag one of our properties that has be refurbed recently but not being a tester my rules and regs knowledge is a bit lacking.
So basically its all about spurs for isolation
1. spurs are required to isolate fridges...
The builder has located the meter box immediately outside the downstairs loo. Now I have reservations about placing a consumer unit in a loo, especially right over the loo itself, but can anybody recall any regulation that prevents it?
Morning gents (and ladies)
I have a job the now at a hydro power station where the client is experiencing a loss in production and believes this is due to moisture ingress into underound electrical joints along the 3km route of the 10core 5 pair BS5308 Type 2 Part 2 hill instrumentation cable...
Hi just carried out an EICR prior to a consumer unit change. The customer has a wet room with a normal baton type accessorie. The ceiling height is more than 2.25 mtrs but the shower head is less than 1.2 meters from the light in a straight line. There is no rcd at the minute but will be once...
We have just published SolarMeter app on Google Play, that simulates solar cell behavior based on your GPS location while moving your android device arounda and also makes calculation for the annual energy distribution at your location, based on panel orientation and tilt. So you basically can...
What are the 'rules' regarding where this switch has to be located?
eg Can it be eg. in the attic with the inverter or must it be 'next to' the main consumer unit? If it were close to the consumer unit but the other side of the wall eg in the hall instead of the kitchen (where consumer unit...
Hi folks
im currently doing annual EICRs on leisure centre swimming pools and wet areas.
The jacuzzi i found, has the control gear/pump equipment adjacent to it, which does not comply with the regs. On speaking to the NICEIC, they said its a C2 and i should put it in writing to the council...
Hi guys and girls I'm new here sorry for any miss spellings . I've recently done my part p and I was told that there was no distance that a cooker isolator should be from edged of cooker is this correct is I'm sure I've seen a 300 mm distance somewhere
Hi,
I need to change an existing bathroom fan to an selv version.
The easiest place to mount the transformer is in the drywall cavity, adjacent to the existing switch.
The cavity is 50mm thick, with space around it, but obviously isn't ventilated.
Is it safe to mount a transformer there...
I am being asked too install a local fuseboard within an outbuilding containing a hot tub, the proposed location for the fuseboard is about 1.4 metres from the edge of the hot tub and about 2 metres off the ground. Does this need any sort of enclosure surrounding it or is IPx4 sufficient enough...
We had a break down call out on Thursday to a stable yard we have just completed , it turned out that the 500m 95mm three phase sub main that was installed as a single phase for the time being until they can afford a three phase meter upgrade has been compromised on the currently used brown...
May sound like a strange question. Is it necessary for the main cut-out fuse to be locate next to the meter? The reason for my question, I was looking to move my meter to the other side of the wall and was given a rough price of £700 to move the service head (about 3 feet away).
If the...
Ok, quick question:
A customer wants a grid switch system installed as they are having a new kitchen installed and have rightly been told by the fitter that the switched FCU's are too close to the sink and hob (2 lots of 2. 2 of which located within 300mm of the sink and 2 located within 300mm...
Gents,
Please can I seek the opinion of those experienced in positioning earthing rods (this is my first time!!!)
I am about to start a full rewire on an old mid terraced house, which is currently unoccupied. The existing electrics are ancient, so everything has to be renewed.
Its a TT...
Hi
Bit of clarification please.
When I want to drill a hole in a joist it says in the building regs book that the hole should be between 0.25 and 0.4 x the span.
so is the span the entire length of the joist from front to back of building or is it between the supports? ie in the kitchen i'm...
Morning,
I've got a job on what was once a dairy farm, it hasn't been used as such for many years, it has a 3ph supply to the house from which the single pahse db in the house is fed with a 3ph supply going out to the old barns and milking parlour.
It appears that the earthing arrangement for...
Hi Guys and Gals.
Have been passed some 16th edition minor certs for an installation in feb 2008. 2 of these are for installs in a kitchen. one for the cooker and one for sockets.
Question 1. Was a Minor adequate for a special location in the 16th?
Question 2. What was the requirement for...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc