I have three outlets (that I can find) that are showing open neutral. I have 80v across hot and neutral, 120v at hot to ground and 28v neutral to ground.
I also have one switch to a light that I think is on this circuit that is not working. If I pull the switch and wire it directly (white to...
In a 3 phase system the neutral carries current that is unbalanced. Okay.
So in a single phase domestic household the neutral carries the same current as the live otherwise the RCD will trip.
So does that mean if we have a perfectly balanced 3 phase system then if I go to one of the phases and...
I've been carrying out quite a few domestic extension first fixes recently which involves providing a power supply installed from the properties mains.
I have always just Henley blocked from the properties main consumer unit tails into a 63/80/100A BS-88 fuse Main switch board then from the...
Newbie to this forum here. I have a question that I need to resolve fairly soon. I have 10/3 from a dual pole 30A breaker using one side of the breaker from the main panel that is direct burial wire going to a junction box outside the house. I need to supply a sub panel to a building. Can I use...
Don't come across this very often - but I've had a CU delivered for a caravan job (not static btw), and it's been supplied with a neutral conductor from the main switch to the neutral bar! Definitely an oversight, but I've got plenty of singles cable in stock, so rather than send it back, I...
I have a Generac GP8000e generator that I plan on back feeding the main panel of my home with the portable generator, power inlet box L14-30a and breaker. First, I will install an interlock between the utility main breaker and the generator back feed breaker. I will only use the L14-30...
My California dryer wall socket has 3 blades shown in picture. I measured across bottom 2 blades = 240VAC. I measured top L-blade with one of the bottom blade = 120V. Is the L-blade a neutral? If yes, why no Ground blade? If the L-blade is Ground instead, then why no Neutral blade?
I tried...
I’ve not seen one of these before and i have a memory of them needing to be upgraded by the DNO.
Just wondering as well what the BSEN is for it. Is it 1361 or 88-3
I have some lights flickering in the house. I was told tightening the circuit breaker wires in the electrical boxes might help eliminate the flickering. Is it possible to tighten the wires without having to turn off power to the house.
Thanks
This one is baffling us.
A supply and DB have been installed .
A section board feeds the DB via a 95mm 4 core swa with no separate earth, only the armouring as CPC.
Outgoing circuits are connected at the DB and SOME in the field
A 4mm neutral wire came into contact with some totally un earthed...
Earth to Neutral 2 ohm with Multimeter on alighting cct. The cable disconnected from the switchboard.
I am new here and appreciate everyone looking at this post.
I come from an Industrial Electrical background and would like advice on fault finding.
My house has 1 lighting RCD. There seems to be...
Hello all.
I am in the process of refurbing my kitchen and I have and old redundant T&E cable coming out of the wall above one of the cabinets which I think may still be live, despite recently replacing the kitchen switch cable and chopping out the extra single & earth cable which was once a...
Why would neutrals and grounds be separated in a main panel? This is a new build with GFCI breakers for the range and dryer; does that have something To do with it?
A numpty question....
In domestic electrics, can one be electrocuted by the neutral wire when there is no short circuit fault?
All the online videos suggest that current flows through live and back through the neutral. If the current going out through live is not the same as the current...
So abit of a random one. But yesterday my Neighbor asked me if I'd be able to take a quick look at their shower as it had stopped working. I said I'd go round an take a look and see if it was something simple enough to fix and get it going again.
Checked the usual things. The solenoid was fine...
Hi
My house apparently is wired in an old fashioned way with what I believe is called a shared neutral ??? Dont really know. But my breakers are special they turn two circuits off at a time and instead of a black wire only, one breaker has a black and the other a red.
So, I need to hookup a...
Why does a 20amp RCBO come with only a 1.5mm neutral flywire when you are driving a 2.5mm power circuit. Aren't you creating a choke, & potential voltage drop. I appreciate it can carry 20amps but it doesn't make sense to me
Hello folks
I am attempting to wire some new Down-lights in my new house , I have wired a few sets up before in previous home however the cables going into my ceiling rose seem to be missing live cables and not like the standard Twin & earth i have connected before . I can see that there is a...
I've Seen this question asked and answered dozens of times. But never like this.
I have a switch that requires a neutral. I do NOT actually have to switch AC power. Yes switch was designed to switch ACc but it's not nnessary for my case.
My switch is just going to communicate over wifi to be...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc