as title. using existing back boxes ( lighting) as original VIR cable in capping and managed to re-use route to save chasing. boxes are tight and nailed in. removal would cause a lot of damage to decor. no earth terminal in box, so my solution was to drill the side of the box and fit screw...
today I was doing some maintenance work on a motor and discovered the motor had no earth at the motor terminal. The motor terminal box is plastic but surely it should still have an earth is this correct? And if so should I run a new 4 core a swa!
The reson why I’m asking is I was told just to...
Hi all,
I decided to change the flex on a small 2kw heater as it came with a fairly rigid wiring to the plug. I was surprised to find there wasn't an earth being used. Also the heater it replaced had a cut-out switch on the base, this one hasn't. Explanation please. Thank you.
Hi guys came across this today, Ze of 37 ohms, surprised me as thought it was a tncs- Victorian house, Db from 1989, no docs- could it be a TT off the water main? 10mm bonding to gas and another 10mm out of sight. The met on the rhs of tncs
block not connected to neutral- can anyone help me...
hi all,
I had my consumer unit upgraded by an eletrician and the test on the main socket circuit revealed their is a break somewhere on the earth wire so no continuity.
The eletrician had a quick look around and roughly located where it could be (somewhere under the floorboards between certain...
Hi all,
I'm new here and want to say thank you in anticipation for the advice you can give me -- I hope it's okay to dive on to this forum as a total newbie with a question rather than just an introduction, but I'd really appreciate some insights!
I bought a Sonoff wifi switch for about £8...
I know it's bad practice but.i opened up a plastic light fitting 2 stories up on the external wall and there's no earth just line and neutral.i feel it's okay but is there many reasons this is bad
I've tried to find a solution on here to this exact scenario but had no such luck.
Could somebody please advise on where I should place the earth wire on a plastic back box with no earth terminal when adding a new metal face plate? The face plate has an earth terminal on it and was probably...
Got to quote a job where the existing circuit does not have an earth.
It's swapping a pendant for 3 Downlights.
The board was changed about 2 yrs ago and has labels indicating no CPC on lighting.
All Fascias are plastic. Where do I stand Regards this, I understand you can accept no CPC on...
Have an old record player that has come into the local charity shop and they want to know if it's worth just throwing. There's no plug on it, but there's only L + N anyway, no earth. I said it possibly wouldn't pass anyway without an earth and said I'd ask. They can bin it if it's going fail and...
Today i did a board change was one of them all in one eicr fix on site board changes "you know the ones that always go wrong".
Well the issue was the house ring.
i had 0.44 live 0.44 neutral and no earth ring.
I have put this circuit on a B32 61009 RCBO.
now how do i stand with the earth as its...
I am working in a property that has the old steel painted switch back boxes that have no earth terminal. Came to light when testing R2 on the switch faceplate screws and got open circuit reading. Earth is present but just sleeved and folded over in the back box.
I intend to ring crimp the earth...
I recently moved house and the previous owner decided to replace the original 2 ceiling lights in the living room with single spots. These produce a terrible amount of light!
I'm planning to replace each spot with a triple cluster, so I brought 2 of these:
Saxby EL-20095 Travis Triple IP44...
I went around a friend of the family today to do few jobs today and found a right old mess.
1960s flat,conduit system ,metal switches ,sockets and chandeliers.
No earth to any light or sockets. No continuity on the conduit from any point to board. (Good Ze)
I can't rewire because the conduit...
Was asked to change a socket in a flat yesterday, when I removed the socket I observed the following,
Slip Conduit & no earth wires, I tested a couple of sockets got a reading of 230 ohms, I put a fly earth down onto the backbox no change.
The system is a tns, with an 80a 30ma RCD as a main...
As title suggests wondering how many people have come across this on micc cable being used but no earth continuity as the copper back box seems to of been cut to allow cables in so no earth at any fittings?
Hi All,
i have a lady that's wants some old antique looking brass wall lights fitted, but they have no earthing terminal on them. Would it be acceptable to solder an earth conductor on them, as she doesn't want them drilled under any circumstances ?
thanks in advance for your help
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc