out

  1. A

    2 way dimmer and JCC V50 cutting out

    Hi guys, just installed new JCC V50 down lights with two 2 way brushed brass dimmer switches from Knightsbridge. When I turn one of dimmers up fully it cuts the light out. And then sometimes they flicker on start up… then if I have one switch dimmed to the lowest and the other is switched to the...
  2. L

    DISTANCE from D/G socket to max reach of pull out kitchen tap ?

    Distance from D/G socket to extended pull out kitchen tap ? Kitchen tap when pulled out is easily with 400 mm of a D/G socket . Not my job . Just asking for clarification etc
  3. Gavin John Hyde

    Amendment 2 coming out next year thoughts?

    Just been reading an article regards Amendment 2 coming out next year. The requirements for AFDD is going to create some interesting conversations with customers as they are not cheap. Unless manufacturers get their act together I would be surprised if in 12 months they have stock or are...
  4. Anthony Deakin

    How to work out no value of Zs to Ze being 0.35 ohm

    Hi all, ive been asked this question A direct measurement of Zs cannot be carried out. The supplier gives a Ze value of 0.35 ohm and the line and cpc resistance as 36.24 milliohm/m. If the circuit is 31metres in length the earth fault loop impedance will be? What is the formula please? Thank you
  5. D

    Cable out of the wall and back in

    Could I run a low voltage cable that comes out of a stud wall and back in again 50mm later to get past a stud. I don't have access above that part of the wall. It would be covered by a cabinet but of course if seen it would look very dodgy. I was thinking of labelling the cable at the very...
  6. dlt27

    2 supplies to property and the one trips the other out!!

    Hi, thanks for any advice. I’ve got a local farmer who has single phase to the farmhouse and 3 phase to the farm and dairy etc. The problem he’s got is when he turns the milking parlour on the house RCD trips. I am a bit stumped as to why and how to remedy. I was thinking when he switches the...
  7. S

    RCD Tripping out

    THIS IS FOR ELECTRICAL NEWS ONLY
    • Steffan
    • Thread
    • breaker circuit circuit breaker doing earth out rcd rcd tripping test thoughts tripping trips
    • Replies: 18
    • Forum: UK Electrical Forum
  8. J

    Swapping out 3 way switch with dimmer, wiring mess found.

    Hey all. No stranger to electronics, I've been building simple circuits as a kid and these days I build computers. I have a kitchen fan with light fixture that the light is wired to 3 way switches on either side of the kitchen. I was going to replace one of the switches with a dimmer switch. I...
  9. M

    90mm Cut Out Downlights

    Hi guys. I went to a property yesterday as one if the current downlights burnt out and damaged the circuit. However when I took out one of the downlights I noticed how big the cut outs were ..90mm. They were in fact too big for the lights actually in there. Can anyone recommend some Fire Rated...
  10. C

    led lights blowing out lights and cooker.

    Hello, I installed an led bedroom ceiling light and it worked ok for several weeks until i changed a bulb and now all the lights in the house don't work, and also the cooker doesn't turn on. None of the fuses have been tripped in the main fuse box. The other plug sockets in the house are working...
  11. B

    Advice on wire sticking out of wall please?

    We are changing a bathroom cabinet and the old one had a cable on it which is coming out of the wall, I'm assuming it is for a light fitting in the cabinet (which it didn't have). Our new cabinet doesn't require any power so I'd like to get rid of the wire. The new cabinet will need to go on...
  12. W

    After your time is out question

    Did any of you maybe a year or so after passing ever wonder if the trade is for you? I.e. after maybe going to jobs on your own and maybe making a few errors or having a few bad days
  13. J

    Cut out mess - who is responsible?

    House to 4 flat conversion. Ryefield board in the hallway feeding 3 flats. Weird that the third phase is being used as earth - time to locate the cutout and the 4th fuse.... So.... We have a three-phase TN-S supply. One phase feeding the basement flat, two phases being taken to the ryefield...
  14. D

    How many of you know your internet browsing is monitored by one of the biggest apps out there.

    Just a poll for curiosity - It was only recently I found out my browsing activity on my phone is been monitored by facebook, what is scary is it does this even when you are not logged into the app', I just wondered how many know about this and how many consider this to be too much snooping? I...
  15. C

    Making electric car seat work out of the car as a stand alone chair.

    Hi all, I have a project to make a range rover evoque seat working outside of the car, Just the motion controls. I have a 12v 30amp step down transformer to give it power. Is anyone able to give me some guidance? I belive I just need to supply power, neutral, ground to the motor. Happy to...
  16. H

    how would i go about working out this question?

  17. G

    Its only ten minutes, burn out socket to change.

    As title, call out to change a burnt out socket. The why? was over use of fan heaters. Quick Zs gave 1.26, something amiss. Did an Auto RCD test to locate source of circuit in this well labelled and populated board. Found RCD to be a stand alone 61009 Now it starts to get interesting...
  18. M4rtyj

    Burnt out accessories

    What is it with the smell from burnt out accessories? That distinct bad fish smell we all know and associate with a burnt out cable or accessory. Is it something in the plastic used in manufacturing of the accessories or is it the pvc cable? I've just changed a 45a shower switch and can still...
  19. B

    Old 3 phase Lucy Oxford main cut out- removing fuses

    THIS IS FOR ELECTRICAL NEWS ONLY
  20. johnwicklover

    Carrying out a refurb on old panel boards, worried about discrimination.

    I am carrying out a refurbishment job on this old panel board and fitting in a new panel board from Schneider. The current supply to this building is a 100amps BS88-2 Gg (assuming). I am planning to protect the outgoing submains with the NSX100 ML 2.2 set at 100 and 63 respectively. I don't know...
Best EV Chargers 2025
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Advert

TrueNAS JBOD Storage Server

UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
JBOD Forums: a forum for JBOD storage server advice
JBOD Suppliers: JBOD Storage Server Supplies
Back
Top