I have an existing but unused 50A disconnect on the side of the house. It had been connected to an AC unit that got replaced. It has just 3 wires run to it - hot, hot, and ground. I want to repurpose it for an RV hookup, using a Nema 14-50R receptacle. However, that receptacle requires a...
They are all connected to the same live "hot" wire, but only the outlet connected to the red wire will work.
Here is a image and a drawing of the wiring. [Yellow = Hot], tested using multimeter.
If anyone has any idea, I would be eternally grateful. Thank you.
I replaced a single pole to exterior lights with a smart switch. Next to it is a 3way to my foyer light. The foyer and the smart switch to exterior works. However I seem to have killed the power to an exterior outlet. In order to get the switch to work, I had connect the red switch pigtail...
I have a light that does not get used and I want to put an outlet where the switch is. The light switch only has 1 blk wire and 1 wht wire on a 2 terminal. Switch that are mounted on the same side of the switch. How can I make this switch into an outlet?
htps://we.tl/t-JHXw09romZ quick share to photo
Hi there. I am trying to convert previous cable network cat5e installed when had non fibre in 2015 to digital. I have an outlet downstairs which used to be my master bt socket converted to t658a rj45 connected via an ethernet to the router. From...
I have a 3 prong 240v outlet for a dryer that reads 240v across both legs and 120 across the ground. When I turn the dryer on and have the multi meter to the ground and a hot leg it shows 120 but if I switch it to the b leg and ground it shows 40 then climbs up slowly to 120. The ground is new...
Hello, my name is Kelvin. I'm a trainee hydraulic engineer in Indonesia. I apologize if this question has been answered before / if this question is too basic. So we have a problem with electric shock coming from an electric panel. This panel runs on 220V AC supply & is used to run an inverter...
Is there enough cable in a 3 pin socket box to change the socket to a freestanding cooker outlet. The cable is on it's own 32 amp circuit and is adequate for a freestanding cooker. I was originally going to have a gas hob and electric oven. I would post a photo, but the thread doesn't allow. Too...
Want to put a GFCI outlet on a circuit. Currently, this circuit is free of any other outlets or switches. Purchased an Eaton 15-Amp Tamper Resistant Weather Resistant GFCI Residential Decorator Outlet at Lowes. Installed according to manufacturer's instructions. Plugged in a coffee maker and no...
Any help or advice. I'm not able to trip my gfci with my plug in tester. IfI push the test button the gcfi will trip but the red light won't turn on. I'm able to reset the gfci with the reset button. The other outlets on this series can be tripped with my plug in tester except for one outlet...
Hi all. DIY here. Electric Dryer (Kenmore Dryer - 796.61552.610) had been tripping the breaker sporadically over the past few months. Recently the dryer has stopped heating though it does still continues to spin and blow air.
Using a multimeter, I checked the double pole 30 amp breaker's...
I have a three way switch going to my downstairs but I’d like to add an outlet to the top of the stairs switch if possible. I’d also like to add a light to the bottom of the stairs as well but that is for later if it is even possible. Any help or advice would be appreciated. The part that...
I currently have a 100 amp sub panel for a 50 amp RV hookup (on a 60 amp breaker). This is about 100ft from the main with 2/4 wiring.
Would a 12000w generator plugged into RV hookup power the house? I think the issue would be limited amps so I could only run one of the following at a time:
1)...
Hello all, I have an outlet box in my house built in the 1920s that I am changing to a GFCI. The wiring is cloth wiring so I have a hot and a neutral.
On this outlet box I have the hot and neutral line wires coming in from the bottom, and on the top I have 2 load wires which go up to the...
Thank you in advance for your help. I recently purchased a home and while removing some built-ins I found that they had a 14/2 wire running inside the built in between an outlet behind the built in and an outlet next to it. I assumed they ran a new switch off the hidden one when they installed...
Hi - I'm trying to add an additional outlet to a circuit in my house. I tested the outlet with a tester, and it showed as correct. The existing outlet is facing the finished part of the basement, but where I am looking to add an outlet is in the unfinished utility room behind the wall. I have...
Bought a range from Home Depot. They supplied a 40 amp cord. Electrician was going to use a 50 amp outlet.
Here is the oven and cord.
https://www.homedepot.com/p/GE-30-in-5-3-cu-ft-Electric-Range-with-Self-Cleaning-Convection-Oven-and-Air-Fry-in-Stainless-Steel-JB735SPSS/314138205...
I'm a DIY'er helping a friend connect a 220v dryer to a 50 amp RV outlet.
The dryer has a Nema 10-30R plug and is in a shed about 4 feet from the 50 amp outlet.
I'm thinking about getting this cord to plug into the 50 amp outlet:
https://www.amazon.com/dp/B08WM3NRT1
And connect that to...
I'm installing a towel warmer and I thought I would include an outlet on the same cable because the towel warmer needs a junction box anyway. Can I run a 12/3 with both black/red hot, black attached to the switch, to the outlet connected to red, and continue the black to the towel warmer with...
Hi,
I want to add a 32a induction hob and 13a oven to my cooker circuit. I was going to make the current single outlet dual and then upgrade the MCB from 32a to 45a.
See photos of current setup.
Does this sound doable?
Thanks
Phil
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc