Bedroom has 5 outlets with 1 outlet that has a switched plug. I want to convert another outlet in the bedroom, that is a standard wired outlet, to a switch-controlled outlet.
Plan:
- Run a red wire from the already switched outlet to the proposed switched outlet plug.
-Of course, break the...
I recently had a solar installation at my home. Immediately afterward, a GFCI outlet in my garage stopped working, had no power, and could not be reset. At the same time, my two outdoor outlets stopped working. I first checked the new breaker box the solar installers put. However, no breaker was...
I have a question on wiring to make sure I am doing it correctly. I plan on adding a new GFCI/AFCI 20 amp circuit breaker to my box and run the wires to the first 2 outlets in a 2 gang box I am installing. I am also installing 2 other 2 outlet boxes. This is in a finished garage. I know how...
Hi guys, I sat a mock exam last week for the written 614 Inspection & testing (C&G L3). All was ok, but there was a question to state the minimum IP code for the front cover of a socket outlet. I'm not sure if this is something obvious or a trick question, but I can't find anything in the...
My wife wants me to add an outlet in a large closet. It would be easy to feed the outlet from a bathroom outlet that is on the other side of the wall. However, I've read that the US electrical code does not allow connecting outlets in other rooms to a circuit that feeds bathroom outlets. Why...
Hi all, got a new range cooker I’m connecting which comes with a 10mm flex connected. The outside diameter I nearly 20mm and won’t fit into the existing cooker outlet plate. Does anyone know of a supplier which allows for larger diameter cables?
Failing that I’ll have to connect into an...
I recently purchased a steam sterilizer with a PID controller and I'm trying to figure out how to power it safely. The sterilizer requires 240v but the PID (if I understand it correctly) uses the return 120v on the neutral wire. My problem is that I have an old house and the neutral and ground...
I live in ranch style home, basement and main floor.
14 years ago when I was young dumb new home owner strapped for cash I installed my own 220 outlet for the oven. I used overkill wire size (cant recall size but its more than I needed) and a 40 amp breaker.
The wire comes out the fuse box...
I bought a single LED bulb today and was suppressed at the cost. As I'm intending to move over to LED which means changing all the bulbs in the house I'm looking for the best place to buy from and that means service not just price.
Hey there!
I removed an old wall outlet. It had 9 wires connected to it. 3 sets of white, red and black wires. I want to install a new one. What outlet do I buy and how do I make the connections? The outlet is not controlled by a switch.
Thanks
Alain
Hello everyone, I am no domestic electrician but I do work as a designer in the railway, low voltage signalling circuits etc. My question concerns my oven. I have just bought a second hand double oven of the internet and went to fit it in my rented house. The existing oven is connected using a...
I'm adding a 30 amp RV outlet to the exterior of my house.
The location I'd like to put the outlet happens to be near the gas main/meter.
Are there any safety or code issues putting an outlet near the gas meter?
Hello,
I am about to install NEMA 14-50 outlet to charge other electric car in the garage and I will run 6 gauge(THHN) wires into the 3/4 in. conduit across to other side of the garage. The electrical panel is outside the garage. My questions are
1. Is it okay to use 10 gauge bare copper...
I am trying to replace a regular light switch with a switch/outlet combo but am a bit lost. There are 3 separate wires coming into the box and I'm not sure which is the light fixture or how to wire this. All 3 whites are tied together (do I pigtail off those 3 for the connection to new switch?)...
I am moving an outlet in my bathroom. The original outlet is where we would like to put a vanity mirror. These outlets are located above the vanity. The faucet is about 6 inches to the right of these photos.
The cable comes from above and is not long enough to reach the new preferred outlet...
I have a 3 wire cable coming from a switch into a junction box and from there it needs to go to a light and another switch while also going out to an outlet that needs to be hot all the time. I know I'll need to have 3 way switches but I'm not sure how to go from the incoming 3 wire cable from...
I'm a home owner, not an electrician. I have a window ac unit that draws 7.5amps. All I have in my garage is an outlet that's on a 20 amp breaker. Will 20 amp work or do I need to replace it with a 15amp Breaker?
HI—having trouble with a GFCI outlet. Unsure if there's much more I can do before calling a pro, but wanted to ask.
I have a GFCI outlet in the kitchen that recently tripped. When we went to reset it, we lost power to the hood fan and stove light to the right of the outlet. The "reset" button...
Hello all! So as the title says and as the pictures will demonstrate, I have received a very old drill press. However, the cord was absolutely destroyed and needed to be replaced. I had no experience doing this, but followed along with YT videos and was able to replace all the wires, and added a...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc