I am carrying out a refurbishment job on this old panel board and fitting in a new panel board from Schneider. The current supply to this building is a 100amps BS88-2 Gg (assuming). I am planning to protect the outgoing submains with the NSX100 ML 2.2 set at 100 and 63 respectively. I don't know...
I have an old 30 breaker electrical service panel (from the early 1980's) that the main breakers are twisting to the side more and more and the cover panel no longer fits properly over them. I have decided that it is time to replace the service panel with a new one, as I feel this is turning...
I have 200amp connection, with the meter and service disconnect at the road (see pictures). House panel is about 75 feet from the service disconnect at the road.
1) Assuming I need 4/0-4/0-4/0-2/0 AL wire sizes (considered a sub panel), exactly what type of wires are required to run from the...
Good day! I have a 200 AMP service with the main shut off installed outside. From there, 60 AMP line to hot tub, separate main feed to what is now my "sub panel" ( main box) in my basement. My dilemma is that my common bus bar is full. As it is now a sub panel, I cannot place any commons onto...
Hello everyone!
I’m a new homeowner and a new dad! I recently just built myself an office on my property and I wanted to run electricity to it.
I currently have the dreaded challenger panel and I wanted to know what breakers I can use with this panel?
I plan to run some lights and several...
I am an owner (not an electrician) and plan to commission building a new house in Toronto, Ontario, Canada.
The home will have a legal basement apartment (so 2x ovens, 2x laundry, etc), 2x car chargers, elevator, some electric heated flooring, electric heated driveways / paths, HVAC, and some...
Hi there, my first post here,
I installed this in 2015 which is a 150 amp GE powermark gold 8 circuit 4 space meter/load center
https://www.homedepot.com/p/GE-PowerMark-Gold-150-Amp-4-Space-8-Circuit-Meter-Socket-Load-Center-TSMF415CSFLP/302751170
Now I want an ADU in my backyard. Power...
I am monitoring my subpanel with a CT monitor and the utility meter with a Zigby reader.
The meter shows consistently 3% higher. So it is either normal loss in the wire, or the utility is overcharging, or the CT monitor is inaccurate.
The breaker for the sub-panel is 90A.
Could anyone...
Hi There,
I hope everyone is good :)
I'm a newbie on this forum. I need a help for my solar panel study case.
Link: https://drive.google.com/file/d/1SAbb5BkIAqL2uNE37mO7jZFWJxZDYDQk/view?usp=sharing
This link contains data for a site which is performing at about 77 % for September 2014. Try...
Been having issues with a pair of linked Actulux SVM controllers.
If the fire alarm is triggered the controllers show 'Alarm' and the AOVs open as expected.
After the alarm is cancelled and the fire panel is reset, one of the SVM controllers goes back to normal, the other stays in 'Alarm'...
We are thinking of installing new ceiling lights, in Standard 10 feet ceiling. We originally have 4 inch diameter light in the hallway. My son would keep the door open to prevent getting hot, however this hallway light was hitting the side, peripheral of his eye, very small and lot of light...
I’m not looking to do any repairs. Just looking at better understanding on how my home wiring is set up. Home was built in 94’. I’m not electrical savvy, I know some things but what would be the reason to mount a main power switch(breaker)from one side of the house yet mount the sub panel on the...
Good afternoon guys. Recently had to make an impulse generator purchase. Looking for some guidance to make my generator use both more flexible and safer than extension cords. Apologize in advance for breadth of information and questions. First time on this forum so any help would be greatly...
where can I get the control end panel " the plastic part "complete with controls etc for a rointe K serie ,it has 11 panels .I am in Dublin .
It is not working correctly ,display goes white
Thank you ,
Niall O Connor .
control panel and electrical installation software for sale.
WSCAD is a Siemens based system.
Has the ability to carry out the following:
control panel design drawings circuits and layouts
Electrical installation design drawings circuits and layouts
terminal layouts
materials listing
automatic...
Hi,
I'm needing to run a raspberry pi computer board near my boiler. The Pi requires 5v at 2.5A.
My heating system is from NIBE and the control panel a SMO 20.
It does have a USB port on the front for software updates but this doesn't appear to have enough current to power the Pi properly. Sad...
Because I have no wall outlet grounded anywhere in the house, I asked an electrician to help and the solution that didn't involved destroying the walls was to wire a power strip directly into the electrical panel (i got one right where the entrance is, I don't know the exact name but every...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc