phase

Recent contents Top users
  1. S

    Why I get only one phase reading current while rest are zero

    Hi I have UPS 50KVA and the inverter output AC voltage is feeding a distribution panel 120/208 V 4 wires when I check UPS display it shows me that output current which is the distribution panel phases as followings phase one = 30A while Phase 2 = 0A and phase 3 = 0A is this a problem !? Shall...
  2. B

    UK 3 phase rcd protection

    Hi everyone, I have been asked to pull in some new 3 phase supplies for 7 new welders which do not require a neutral connection. The client has specifically asked for them to be plug and play and rcd protected, which is fine as they are under 32amps. I will be running in 5 core swa's for...
  3. G

    single phase compressor motor

    Hi, I am looking for a connection diagram or sugestions for a 2.2Kw single phase motor to drive a compressor. The spec plate shows that it can be run at 220-240 v / 460-480v 50Hz. (unusual for 50Hz) At 220-240 volts FLc is 16A plus startup inrush. so I should like to run it at the higher voltage...
  4. L

    Wiring for single phase supply

    Looking to use this brooks Compton motor as a replacement in an electric cement mixer. can anyone tell me if it is designed to operate off a domestic single phase 240v supply? It looks to me as though it could run off either a single or threes phase supply but I’d be grateful to hear from...
  5. Y

    Singel Phase Wiring for TeSys LE, enclosed DOL starter, 12...16 A, 240 V AC coil

    Hi, Trying to wire this 3phase switch as single for a table saw, told I could do this from guy at Haymans, even told 2nd time which wires to connect, didnt work, other tradie at work couldnt work it out either. have L1 and L2 and N and T1 and T2 on bottom from diagram any help please?
    • yozter
    • Thread
    • ausie elec dol phase starter wiring
    • Replies: 2
    • Forum: Australia
  6. R

    Table Saw 3Ph conversion to Single Phase

    Hello Everyone -- So, I am looking to buy a used 5HP 3PH 208 V 10 inch Table saw --- (Motor Plate Data in Image) I am a DIY'er and in this case I would not attempt to do a 3PH to Single Phase conversion myself -- (I have looked at many videos and read several articles about how to do...
  7. 3

    Contactor. Proving dead . 3 phase .

    When working in a control panel. If I needed to replace a 3 phase contactor do I need to carry out a 10point check to prove dead on just the mains isolator. Or do I need to 10point check the mains isolator and then another 10point check on the contactor before removing. Many thanks
  8. E

    Hi Zs on one phase only

    Anyone come across this before? I was asked to do a Zs on a 3ph surge device; L1 was around 6 ohm, L2 & L3 around 0.11. Wired in singles from a Ryefeid and one earth conductor so cannot think why this might be low on one phase only.One thing I did see was L1 fuse at Ryefeid was doubled up with...
  9. K

    3 Phase connections

    Good day to you. I need electrical drawings urgently and hopefully there is someone that can assist me. They are all for electrical trade test. Taking into consideration it's three phase. 1. A 2 Speed starter with selector switch and motor with control circuit 2. A manual 2 speed starter and...
  10. J

    3 phase problem after spark did 5 year safety inspection

    Hi lads 5 year safety inspection the spark put the tails back and later line 2 of the 3 phase blew blowing the box off the wall and taking out the main fuse on the same line into the building can you all just say quickly what you think the spark may have done wrong ? Cheers
  11. W

    UK 3 Phase Smart Meter EDMI ES -30 B Install

    3 Phase Smart Meter EDMI ES -30 B Install I have a question regarding the potential replacement of my existing EON supplied ELSTER A1140 3 phase meter which is currently providing E10 switching times for our all electric home. The house has an old electric storage boiler and the system is...
  12. J

    3 phase meter problem

    Hi there, I built a house with ground source heating 5 years ago and it's a fairly large house so I have 3 phase supply 80 amps per phase. I had a regular meter it was a Elster A1140. I read this every month on the 1st and logged the readings so I have a good idea of my usage patterns. Ground...
  13. A

    1 phase 2 pole 400v pump wiring

    Hello. How i should connect this 1 phase 2 pole 400v cooling pump? If i apply 1phase 230v and neutral it Will only growl and "spin" very very slowly. Thank you for help.
  14. S

    3 Phase Distribution Board Dilema

    Hello All So I'm not long out of my college days and unfortunately I didn't have a lot of exposure to three phase and commercial wiring systems. I have a three phase switch fuse Isolator rated at 200Amp supplied by the landlord. I need to split this across two Proteus distribution boards, the...
  15. M

    G99-SGI-3 4.4 kw set export limit phase to neutral loop impedance test on site

    G99 SGI-3 4.4 kw set export limit phase to neutral loop impedance test on site 0.309 ohms and dno max being 180 m ohms or 0.018 ohms so site reading are well over the top or is this not unuall for 1950 lead cable TN-s
  16. X

    3 Phase Vacuum On Single Phase Supply

    Absolutely losing my brain here guys What I would like to be able to do is power our 3 phase motor on a single phase supply. Thought I had it all figured out, motor is dual voltage, on 230v its pulls 30amps 8.6kW rating. Nice cheap option was a dps (compared to getting 3 phase installed or a...
  17. X

    UK 3 Phase Motor Star/ Delta phase conversion

    Hi Guys, We have a CNC router which uses single phase for the spindle, stepper motors and control box. This is all wired in and working correctly. However, the CNC also features a vacuum bed, powered by a seperate 3 phase motor. We have no 3 phase in our shop, the motor is labeled as 4kW...
  18. O

    Wylex 3 phase board fitting.

    Do I need any more than this to fit the above board, does it need a fitting kit for the switch or anything extra to get it up and running (tails excluded obviously)
  19. T

    Wiring 3 Phase/Single Phase Hob

    Hi, searched the forum but cant locate anything similar so apologies if ive missed something. Ive got a new hob to install in the kitchen (Cookology CIH602). Ive got a dual cooker connection plate with the oven already connected and intend to connect this. Looking at the manual, it can be...
  20. Aegir01

    Hooking up a bandsaw from single phase

    Hello all, I signed up here for a little help. I bought a 3 phase bandsaw and went down the rabbit hole of VFD’s etc. ‘The motor is 3 phase 400v and I have 1 phase 240v (Australia) . So I bought a VFD that has an input of 240v single and an output 400v three. It’s currently in the post. I...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Green 2 Go Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses Heating 2 Go
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

TrueNAS JBOD Storage Server

UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
Back
Top