Hi I’m getting a new kitchen fitted, there’s a existing socket outlet fitted into a pipe chase, for the rewiring of new socket outlets is it still ok to have a flush socket fitted into the pipe chase, the pipe chase contains a soil pipe from the bathroom above. If it does or doesn’t what is the...
Hello
The questions are regarding the Sensors used with the Thermostat in a Condominium building.
What are 2 pipe & 4 pipe sensors? What should be the typical resistances of each one?
Hello, I hope you don't mind me dropping a message here. Please move to the appropriate place if required!
I work for a company who manufacture pipe carriers (the type you see on top of a vehicle) and I'm looking for some end users to talk to help better understand your general needs.
If...
Hello,
Carrying out remedial work on a commercial site and I've come across a metal out building that has a water supply to it. The water pipe comes out of the ground behind the building in copper but enters the building in plastic. There is conduit on the outside of the building next to the...
Hi guys
I am working in a warehouse where there is an inactive gas pipe and disconnected gas meter. The DB which has been upgraded now is on the other side of the warehouse. My question is does the pipe need to be bonded? Incoming metal gas pipe I believe is 28mm. Distance from that pipe to DB...
Non contact pen picking up current on my water pipes. I've turned off the boiler but it's not that. Found that it's the down stairs lighting. I'm starting out on electrics so medium to low experience. Is this a normal thing?
This is my first post and I hope I explain it correctly/ Simply. 1100sq foot single family home, 100 amp service. I am having an electrician replace the front part of my service entrance from the weather head to the meter socket. The main panel was updated about 10 years ago and is not in need...
Good afternoon one and all. I, like many non-electricians are having issues regarding the need to have domestic water pipes (plastic entry to the property) bonded prior to an EV charger being installed. I have read a number of articles on this forum which quickly leave me behind with the...
Hi,
Our cooker is LPG, fitted on the inside of an outside wall if that makes sense. The gas pipe runs internally then through the wall to the regulator and changeover unit mounted outside, around 4' off the ground. The pipe doesn't go underground at any point.
My understanding is that it...
A 'Sunday challenge' for the qualified electricians....
Can anyone explain why a built-in gas meter housing box
that is located 600mm above a block paved driveway, with a plastic (Polyethylene - MDPE) supply pipe and no extraneous conductive part, could result in a dangerous potential...
Good Evening.
I am in the process of making some slight alterations to my Utility room, and there is a Twin and Earth cable that needs re-locating.
It is a 20Amp Radial circuit for the socket outlets, solely for the Utility room, protected by a 20 Amp MCB and 30mA RCD.
I need to re-locate the...
Good morning everyone. I’m looking at getting an EV charger installed at my home and the company is requesting that I earth bond my water supply piping. The main water pipe entering the property is metal, then there is the stop cock, and after about 100mm it turns into a plastic pipe (total...
Q. imagine you have discovered a water pipe in a bathroom that has been repaired at some previous time using a plastic connector
-So I am a little confused about this question because, I am being asked to explain why this situation can be dangerous also.
how can you "remedy" the situation...
Hi Guys,
I'm looking for some opinions, I've got a customer with a gas meter in an in ground box (see picture). The pipe to the meter is plastic as the meter was moved a few years ago but its metal where it enters the house from the outgoing side of the meter.
Would you bond this?
The customer...
Hi guys
I’ve seen people state in forums that it is permissible to bond a gas pipe as a continuation of the bonding of the rising water mains. Can anyone supply proof/documentation/official guidelines etc., where this is explicitly stated.
Below is an image of what I am planning. My gas safe...
What do you guys think about using decommissioned gas pipe which is welded throughout and 4" industrial in steel.
I am clear on regs that say you cannot utilise a gas, oil or water pipe as a bonding conductor but this would effectively safe a lot of time and money.
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc