I've got a cooker hood extractor, it only has a live and neutral cable, I've only got a single socket to install it. Can I put a 13A plug on the end of it?
I am as newbe DIY as it gets when it comes to electrical work.
Here is my issue at my home. I have a light switch which controls the recess lighting in the living room as well as all the plugs. A pretty poor design IMO especially since that room also acts as the TV/entertainment room. As of...
Is it possible, if and why not iff so,
To fit an EV motor and controller directly to the stator output of a 125cc motorcycle engine, (pre regulator)
Using a fixed throttle set up to increase revs to the required output and to bring it down to the engines normal idle revs for when stationary...
Hi guys so basically I had a shaver charger wire with a 2 pin plug, and cut the wires and put it into a 3 pin plug. Is this ok or will there be problems? The wires from the shaver charger seem thin. Please see attached image. It's a standard Philip's charger wire.
I have a plug that is on a switch, but I want to make it always hot. It is also a 3 way switch, so I am not 100% sure what to do. I'm somewhat experienced with electrical, but I can't get an electrician to my house due to the quarantine.
My cooker was wired to a 13a socket in the space behind the oven in a Persimmon new build, wooden construction. Some idiot cut the insulation back and reduced the strands in order to connect it, The fuse heated up. The 15 amp cable arced away but the fuse is still intact. Surely this is not to...
Ive got a driveway light on armoured cable. The cable comes into the house under the stairs. Can I put a plug on this cable and plug into a RCD socket.
I am looking to buy a generator for my mobile catering unit. Most I can find in my price range have a 32amp 240v single phase socket. My unit is setup to connect to a 16amp plug into the consumer unit with an RCD. My question is can I use a 32amp to 16amp conversion lead rather than having...
My tumble dryer has been in the same position and worked for years today no power when I check plug hard to remove. Which I discovered was because melted, dryer was plugged into extension lead. What would have caused this? Do I need new dryer or can I just fit new plug? Thx
Hello guys.
Im a plumbing and heating guy. I work with low voltage all the time and get calls from property managers everyday.
I looked at a range tonight. They've blown two boards and were told by the appliance sales company that they had an issue at the plug so I went and had a look...
hi. today my power started switching off, but not my lights. only my plug sockets are going off. i’ve unplugged everything from all the sockets so there isn’t a faulty appliance. is there anything else i could try doing?
Does anyone know of a tool for tightening up the barrel of DIN type cable connectors
Company I work for now uses a lot of this type of connection often with limited access for fingers
I've seen a phoenix contact version with a hex screwdriver and a cam which slides on to the end , this hooks on...
Hi I have just bought a new cooker and it has a cable and plug on it but my old one doesn't. Can I put a socket on the existing cable (6mm I think) and then just plug it in.
Hello. I live in MA, in case it has any bearing. My daughters gave me an inflatable hot tub, and my question is re: using an extension cord to plug it in. I had one several yrs ago plugged into one of my outside outlets but they're not working at present (only 1 is attached to the house so I...
Can anyone help in tracking down this plug used on a Salton hot tray power lead and cooking hot pot (1970's era). In a recent move the leads have been lost. It's made by 'Nettle'. I managed to borrow a lead for Christmas from a friend but need to buy 2. Have searched web without success.
https://www.jmldirect.com/offers/buy-it-now/plugull-plug-removal-attachment
I feel that given the longer length of the earth pin it will actually stress the plug and the socket. British plugs can be a bugger to pull at times, but I don't think this is the answer..
Hi, so I am looking for a good solid answer even though it might seem obvious. I need the proper technical answer so I can stop being bothered.
So I have a proper backup panel installed in the house with the proper plug outside to receive a generator 4 prong plugin. I have been loaned a...
been living in this house for 8years after it was fully re-wired, today the kitchen plugs trip the RCD when any power is drawn (apart from the cooker CLOCK), all the appliances are fine, any socket that I use trips the RCD, any ideas
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc