I understand that some vehicles do a check on the earthing resistance before they allow themselves to connect to the charging point, so irrespective of whether the earth resistance is in line with the regs, it may not be 'acceptable' to some vehicles.
Does anyone know what value of resistance...
Hi I have an illuminated bathroom cabinet that I want to put into the bathroom. It’s 240v . I only have a 240:110 shaver point, so I wondered if it is possible to connect the cabinet someways?
I have a very ugly and large cooker socket above my gas cooker. It has a single plug point which my cooker is plugged into for the ignition/timer. It is in the way of having a splashback installed. How easy would this be to move a few inches to the right and replaced with something a bit more...
Hi all i am not sure if this is the correct place for this question.
I am to install a phone point down the hall in a mates house but he has virgin media and the phone line comes off the router.
i was thinking of taking a basic 5 meter extension lead and pluging the male end into the router...
Hi there
I’m unsure of what wiring I need to run for an EV charging point and have read that there were new requirements launched in January 2019. Please advise. Thanks
At some point I'm going to get asked to fit one of the above and I'd like to know a bit more about it from some people that have already fitted them.
I've had a look through section 722, am I right in thinking the following:
1. Has to be on a dedicated circuit?
2. Has to have Type A RCD...
As the charging point must be outside the DB equipotential zone (separate earthing rod), are people using 2-core SWA for EV points and eathing via the armour?
Hi all,
On a recent job (electrical) the customer asked if I could add them a point to hard wire his computer to his internet. I put him an ethernet socket at each end, ran a piece of cat 5 in between and terminated with punch tool as per a bt socket. Customer reported not being able to get...
New circuits. Ra of 229 Ohms therefore the rcds are for fault protection by design. Zdb of 0.29 (10mm gas bond) so are the rcds classed as additional protection?
I'm considering a career change or trying to implement a 50/50 split between my current work in IT - largely working in a technical capacity as a 3rd line support analyst and re-training to get into the green sector and do part-time work (or potentially a full career change) either fitting PV...
Hello,
I need to add a switch for an outside light. The obvious place is near the back door but that is where the fire call point will go.
Is there a minimum distance in any regualtions between the two?
E.g. to prevent someone from accidentally pressing the call point while trying to press...
I've been working for a firm for a number of years now with jobs on the side, recently gone full time solo. Everything I've done up until now has been either day rate, or price work.
I'm based in Surrey / Middlesex by the way, most of my work is in the areas surrounding Heathrow airport and...
Good morning fellow electricians. Now, as I am sure you have all been enjoying, I have not been on here much lately, as I am jacking in very shortly, or at least not renewing my scam membership. So, with only 20 days left, it has just occurred to me it might be a good idea to install myself a...
Hi, I just have a few questions in regards to testing an RCBO circuit
Is there a requirement to test at either the furthest point or the DB or is it down to the testers discretion.
Do the test results differ?
What tests on a circuit will trip the RCBO when you are away from the DB. Is it...
I have a nice job on in a few weeks which includes wiring up a solo chargepoint EV point. The pod doesn’t have its own RCD like Rolec do.
I am rewiring the house and intended to use either a type A RCD or RCBO.
As they also detect small levels of DC leakage.
I use BG consumer units but I...
I am currently doing an EICR in a warehouse and one of the circuits is for a Fork Lift Charging point (32A) In Light of the 18th Edition and all circuits being protected by and RCD, should I recommend that the MCB that is feeding that circuit at present be changed to an RCBO ??
Hi,
I know there are many ways to achieve this. I just wanted to know that the diagram I have drawn for this 2way switch would work. Just having neutrals at each point, for future smart switches. Thanks and merry crimbo
Hi all,
I have been asked to install an EV charging point for a friend who doesnt have an electric vehicle but would like either a cable ran in or a charging point installing to future proof his home.
My local training centre runs a course for EV points and I was wondering if the course is...
We have a door that will be in normal use but is designated as a fire exit, however, there are all glass windows site managers that think they know it all has said "can't it go on the wall some three meters to the left" even if building control accept it I don't think it would comply with the...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc