Fluke Corporation has identified a safety issue affecting certain Fluke T110, T130, and T150 Two-Pole Voltage Testers (“T-Pole Testers”).
As a precautionary measure, Fluke has decided to voluntarily recall all of these products and provide affected customers with new and improved equivalent...
Hi,
New to the forum and not an electrician so be gentle .
I'm looking to install an outside electrical supply to my shed for lighting and some sockets etc and have the armoured cable ready to go. However on looking at my consumer unit there isn't room. However the MK RCD is taking up 4 spaces...
With for example the Wylex NXHL1B Single Module DP range of RCBO's there is (at last) a sensible solution to RCD protection for all circuits individually, but only up to 40 amps. Is there a manufacturer doing 50 amp single module double pole rcbo's e.g for thirsty 10 kw or 11 kw large cookers...
Evening all.
I may have to fit a weatherproof junction box to a hollow, round metal pole.
The junction box will be around 20-30cm from the ground and 2 x SWA will enter from the bottom (CW20). 1 x rubber flex will leave through the back of the JB into the pole and up to the top where the light...
If there is, maybe you can help me identify what these new boxes are that have recently appeared on all the overhead LV distribution poles/lines located in Devon.I have never seen them before on any overhead power distribution systems.
Cheers.
So Put a couple of LED panels in new fabricated unit finished install and tested Zs, as you do. Fine on L-N not fine on L-PE, KT65 DL says voltage on earth 79v to be precise(ish?) Ok so just double check with Fluke T130 get 44v. This is present no matter what the state of the lights are i.e...
Is there a double pole Rcbo available that i can fit in a consumer unit i would like to use a doublebuss bar and have individual protection for every circuit all the rcbos that i have found so far have a flying lead for the neutral this seems unnecessary and i think the way i would like to do it...
I'm looking to install lighting in my garden, part of the requirement is that the circuit is hooked up to a photocell so that by default they will illuminate at night. As our bedroom window may suffer glare there will be occasions when I want to manually override the photosell and turn the...
Been to see one of my jobs today and this is what I noticed:
Background:
The property used to be a bungalow and is have a "full" 2nd story added
The tarpaulin to the left is the based on the wall which is to be built upwards ........
So my question is - can anyone point me in the direction...
brand new without the boxes 115a contactors with 110v coils.
3 for sale I am asking for offers around £150 per contactor these cost £300 when I bought them.
Ok, so having been offered & bought a Bosch GCL 2-50CG combo laser level at a really good price ( second hand, but unused), I'm looking for recommendations for a telescopic pole. Prices seem to range from £50-120, so anyone have practical experience of say Bosch, De Walt or Stabila telescopic...
Question I am trying to trace a triple pole mcb. The panel that the supply goes to has only a 3ph supply no neutral. The building is a NHS site and has many distribution boards some marked up correctly. The problem is I can't go round knocking of breakers due to equipment etc. Was looking at a...
Hi all, I have got to build a small panel for a overhead crane long travel drive motors (Old Street crane) The motor is is a 2 speed pole changing motor 750rpm and 1500rpm it needs both slow and fast speed and it also has a link between across 1ph of the slow and fast winding in the motor...
Just bought a xpelair 12v humidistat 100mm fan to go in zone 1 and reading instructions it asks for a d/p switch. Is that the regs ? I assumed it could be wired as normal i.e. live from light switch and perm live etc .. having looked into it a bit more it seems i could go 230 v if rcd protected...
Eh up :)
Section 721: caravans and motor caravans
721.43.1: Each final circuit shall be protected by an overcurrent protective device which disconnects all live conductors of that circuit.
Any tips for sourcing 2P circuit breakers (or RCBOs) and a small DB? Probably only 2 circuits, possibly...
My client wants to fit a very large floodlight 240w LED (Wirefield LED Commercial Floodlight 240W - http://www.rexelenergysolutions.co.uk/product/2500671142/Wirefield-LED-Commercial-Floodlight-240W-) to a telegraph pole. I was wondering if anyone knows of any brackets to use to attach to the...
Hi,
This is for a boat with 12V electrics, so most parts are similar to auto electrics. For a new engine control panel I'm looking for two push buttons, both need to be two pole changeover. Does anyone have any suggested sources?
FYI this is to replicate the design that some manufacturer's...
Good morning,
Quick research question, can you use a triple pole mcb to power 3 different socket circuits in a factory, helping out the maintenance bloke never heard or seen it before ????
Any suggestions, all cables are fine, was moved from a single pole rcbo to a double pole yesterday and I think appears to be something to do with the generation meter as this is the only issue in between. Does the system have to be on a single pole rcbo?
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc