Hey guys. Just wondering how you prepared for the Practical Assesment? If you have already completed it you would know that there is 1 practical Job and 1 testing job. I am a little nervous as you only get 3 strikes and after that you're out (failed the whole course I think).
So can someone...
2330 L3 unit 302 inspection and testing practical completed today, was much easier than expected. so if anybody is worried about this, I wouldn't be.
got the written next week which i'm expecting will be a bit harder but i should pass it ok.
the most difficult thing for me is the stupid health...
Hello
I have my 206 exam this week and am somewhat apprehensive about it. i have no experience in the trade, am clueless about most circuits. This one is a radial circuit I think. Is that the same as ring? We are expected to fit armoured cable as well.
Does anyone have any advice for me...
im looking to get into the solar pv industry. im a self employed domestic electrician and registered with elecsa. i want to get into the solar pv but obviously i would like to have some practical training and gain valuable experience before i pay out for the course and mcs registration. has...
I'm doing mine in the morning and we've started talking about it on another thread. To keep that one clear I've started this one to help others, its to late for me besides I've had loads of help from the forum and I think I'll pass this due to the help and advice given to me. So please add...
Hi,
I will be doing my 2392 the end of this month.
I have not touched a test meter for about 8 - 9 years since doing my am2.
i just wanted to know what the course involved i.e practical wise?
Is there anything i could do with brushing up on before the course? or will the course cover...
I didnt answer this question as part of my 2392 practical..I can jus about remember it, i wasnt sure how to do it, any help would be appreacited..thanks
A consumer asked to install a heater in a conservatory.
3kw Heater
Length of Cable 25m
Design the circuit.
1. Cable Size =
2...
Hi, i have my 206 and 204 this week and havent got a clue what it will be on if anyone has done it recently can you let me know anything you know about it please?..
On an intensive course have passed all the theory of level 2 with good grades same with the 17th regs exam and c&g pat test...
I have my practical exam in a week & haven't really done any 3phase testing & i am led to belive that there is a 3 phase motor circuit on the rig?
So what i'm asking is how would i carry out an R1+R2 test on it & also the Zs & finally what do i need to do with it in regards to IR test were the...
Hello
I have managed to pass the first 3 theory tests including the 204 theory exam, I am worried about the practical exam though. I have got to test the fitting using a multimeter and answer a few question on some extractor fans on a 3 phase system. One of the questions is about why there is...
Help!
Currently doing the practical test for Level 2 2330. Have to inspect and test this week coming. I think I have a good grasp of all the dead testing we need to do BUT have just been swotting up in the Onsite Guide and I've found something that has not been mentioned so far at college.
One...
Hi Guys,
I have my 2391 practical exam in a couple of weeks time. As I don't really do any commercial testing, can anybody tell me if a contactor controlling a motor is considered vulnerable to an IR test? I assume there is a coil that wouldn't appreciate 500V?
Many thanks
Hi. By trade I'm a qualified mechanical maintenance engineer with 30 years experience and recently I've been trying to diversify in order to gain not only new, but continual employment.
Over the last couple of years I've passed the nebosh health & safety qualification, the city & guilds 2377...
Hi Guys,
Got my 2391 practical tom and the meter Im using is a "Metrel instaltest" from Alphatek, simular to the "Metrel easi-test". I want to know when testing for Ze on the 3 phase board, do I connect earth lead to earth bar, neutral lead to n bar and test each line? Or do I put the neutral...
Hi guys,
Have 2391 practical tomorrow morning and the only thing im unsure on the 3 phase motor circuit not done a great deal on 3 phase testing
For R1 R2 do i take a reading for each line and neautral ?
do i disconnect from motor and just feed from db to there ? or commando socket outlet...
I am starting to struggle with keeping up with the Jobs. And I'm scared I will not finish them and fail the course. I feel comfortable with the theory but a little nervous about the practical side at the moment and I'm actually loosing sleep over this.
Any tips for me? :(
Thanks.
Hi Guys,
Can anyone enlighten me on what is involved in the practical ?
sat theory few weeks back and am quietly confident but would like a little heads up on the old practical many thanks
Hi Guys
I am due to sit my practical exam next week and I could do with some sound advice as I am scared stiff .If it is a prriodic inspection I am doing and I do the live testing first before carrying out the Ze is it ok just to switch of the isolator of the DB and then disconnect the main...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc