Hi,
I am due to sit my 2392/1 practicals soon and during the course of my revision have come up with some un-answerable questions.
2392:
1. Are we required to perform live Zs checks in addition to working out Zs for each circuit?
2391:
1. what percentage Inspections should be performed on the...
I was on here a while ago asking about the 17 day wonder courses, still not been made redundant, but missed the boat for starting a course in September.
I've been wondering how much of the course is passed practicaly, and how much is done through exams.
If I were to buy a book,
Basic...
a big thank you to all those who have given advice on testing issues in the last few weeks on the forum .passed 2391 practical exam a couple of days ago . head fit to explode by end of exam
Hi
Been asked by a customer if I could carry out a PIR on an industrial unit he has. Have had very little experience in industrial testing. And since doing my 2391 a couple of years ago which only skims on three phase testing.
Was wondering if any of you knew of any test center's where they...
Hi all,
My brother called me today to ask if I would like to do some work for him at his house.
I have to meet him tomorrow but basically what he said he want is the following:
Existing switches to be relocated to a higher position as they are too low based on the regs (this was advice...
Hope I don't screw it up.
I test often enough in work so should be OK, just been getting used to a new multifunction in work so hope that doesn't throw me.
Anything last minute tips appreciated.
hi i am new here and am after some help please please. am going though my books as i have just found out my my level 2 practical exam tomorrow witch i thought i had a couple weeks untill got to do it. and and am having a problem. . i havent had much to do with testing and think im going to fail...
I am completing my 303 practical exam tomorrow and wondered if anyone knew whether, on the certificate, I needed to complete the section recommending "next inspection date" or whether this was omitted. From what I understand the faults will be on more than one circuit and the inspection and...
What a day started of with 302 and 303 practical passed 302 with Credit and 303 with Distinction :D.
Then to top my day England play a half decent game of football for a change much improved...Happy as larry going have a couple of beers...:cool:
Hi everyone
Just doing last minute revision for the final practical (i.e. Periodic Inspection/Fault Finding) on the 2330 L3 (Tue 22nd :eek:) & I've just stumbled across something that may come up, but I'm not sure how to classify it.
If there is a bridge made on a ring final (i.e. a ring...
Hi all got my Level 3 exam next Wed and noticed there is a edison bulb holder on rig to check polarity do you go from centre pin live to earth on r1+r2 test????
Also there is some micc cable how do you do r1+r2 on this as you would normally, at the switch will there be a earth cable in the...
Hi, I am doing my 2391 practical tomorrow. I thought I understood it all but realised I don't! There is a 3-phase distribution board which supplies a single phase distribution board. I am fine with the 3-phase side of things. When measuring R1+R2 of circuit of single phase do I just do it as...
Hi, I have my 2391 practical tomorrow and need some urgent help! I am fine with everything except the phase sequence test. There is the 3-phase board, 3-phase isolator and then a 3-phase motor. What i'm not sure about is where to do the tests and is the installation live at this point? Usually...
Got my 2330 lvl 3 practical on Monday, but i have not been given the opportunity to have a go at the installation which we have to test. I’m pretty confident about most of the circuit’s except the motor circuit.
1). is R1 + R2 taken at the contactor or is the contactor manually held in and...
when doing the insulation resistance test on the three phase board do you isolate the single pase board before doing the test or leave it switced on with all the circuit breakers on including the dimmer circuit ?
doing the test with the links attached etc
Hi
I have passed the written 2391 but failed the practical as my employer wont let anyone test until qualified which is currently no one!..
So having no daily practical testing experience i have built a test rig and i want to buy a meter to practice with.. I know its a lot of money but so is...
Procedure for testing
Lock off procedure
· isolate installation
· lock off and place key in pocket
· post warning notices
Prove dead as per GS 38 recommendations:
· Select an approved voltage tester that conforms to GS 38 requirements
· Use a...
Hi Guys
I passed my theory paper last november :D, took my practical in march but failed that on the full test rig (lack of time) and the 12 visual (only got 9).. My employer doesnt currently do any testing making it hard for me to learn and practice the practical.. I had to fight to with my...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc