project | Page 4

project

Recent contents View information Top users
  1. R

    How to wire small AA battery project

    Hoping someone can help with this small little project. I reload ammo and I want to make what is known as a "vibrating powder trickler", basically a funnel that fits into a hole in a small aluminum block (roughly 3/4"x3/4"x2"). The end of the block has a hole that meets the vertical hole where...
  2. D

    LED light strip project suggestions

    Hi everyone, I'm after some advice/suggestions/confirmation please. Looking to install some separate runs of LED strip lights as shown below. Thinking I can split it 3 ways to cover the 5 areas, however, with little experience towards this and going off google I haven’t had many clear answers...
  3. A

    DC switch aquarium project

    Hi all, I'm not an electrician so would appreciate some help from all the people with the knowledge please. I'm making a power supply to operate several pumps for and aquarium off one plug I'm going to use a MW HLG-320H-24B PSU To power 5 pumps all pumps are 24V and are maximum 52W I wanted...
  4. C

    Kitchen Led project advice (DIY)

    Hi all New to the forum and wanted to some advice for a project, although I’m not an electrician I’d consider myself able to do some handy work. Im wanting to put some led lighting under my kitchen wall hung units, I have 3 sections of units that I will putting the lighting on, I will be...
  5. Lucien Nunes

    Lucien's new video channel - first project.

    I'm going to make videos. Yes. Must make videos. So this here's not a video but I promise I'm making one to go with it. My workshop is very full, been flat out over the 'holiday'. There's a broad range of different projects on the go, that you won't usually see in the same place. Here's one of...
  6. M

    UK I have a project that i need some advice on....

    Ok, so i purchased an Airbus A320 Reading Light from the cockpit and i want to convert it to a desk lamp that runs off standard mains. The reading lamp: 28V DC @ 100Ohm resistor dimmer powering a 11.5W Halogen Bulb The house: 200-220V AC 50/60 Solution 1: Try and use the existing 28V DC...
  7. Dan

    Tiling Advice and Tiling Project Management - ElectriciansForums.co.uk Blog Feed

    Tiling Advice and Tiling Project Management[/] Tiling Advice and Tiling Project Management with a Personal Approach When you’re looking online for Tiling Advice you get a minefield of information, usually online shops with blogs that just want to tell you about ‘The Top 5 Bathroom Tiles This...
  8. Mark Wright

    Switch 2 port Valve with Light Switch...........for project only

    This isn't for central heating really this is for a project Can I switch a 2 port valve like bellow .I.e is the "Switch line" 230v? MCB >>> Junction box >> Line, Neutral, Earth >>> 2 port valve ........................................>> Line split to Light Switch >>> Connected to SL/Orange of 2...
  9. L

    a shove in the right direction please ! 2365 design project Q3

    Hi guys , hoping someone can help I was due to finish the 2365 course in April this year but with 2 weeks to go some virus came along ( you might have heard about it ? ) just back into the training centre and got the last science exam finished off with merit so quite a relief . unfortunately...
  10. L

    City and Guilds 2396 2020 Project.

    Is anyone doing the latest City And Guilds 2396 course and having the same problems as myself with the distances on the project, what have you done to rectify this? Also where can I find the max ZS for MCCBs.
  11. J

    Advice on fatal current (research project)

    Hello, This question is purely for research purposes. In the event that an appliance (hairdryer) was dropped into a bath with a person on it, and a circuit breaker was tripped in the consumer unit, could this shock still prove fatal or would the breaker save their life? I know that this is...
  12. S

    Electrician Jobs Rotterdam ship conversion project

    Electricians wanted for ship conversion project in rotterdam , 56 hours a week , hotel paid for and allowance to travel back to UK approx every 6 weeks for a week , £280 a day , paid all day sat for 6 hours , send CV to [email protected] , no BS , genuine job , genuine qualified applicants only .
  13. U

    Hi all I am on level 3 and have not yet started my design project

    Anybody got any pictures of there drawings please help me thanks
  14. P

    DiY - Car Project

    Hello, I would like to run a custom electronic engine control unit on one of my vehicles and to avoid cutting up the factory wiring harness. To do this I have found a 60 pin ECM plug from a breakout box and would like to connect the pins to flying leads. These leads would then go to the new...
  15. V

    Free ESWA heating mats to give away- excess from old project. New, unused

    I have some ESWA heating mats to give away to anyone that can use them. I had them for a project in 2003 which didn't need them in the end, and they've been stored in a dry place ever since. They are completely unused, and free to a good home. Mats only, no thermostat. You pay the postage
  16. S

    Can I ask this DIY question?

    Dear all, I'm a computer programmer but never had any formal education in electronics (although I think I know enough on how to isolate circuits). I work in a company that does a lot of community outreach by allowing its employees to meet clients by driving company cars. However...
  17. H

    2365 design project

    I am a student currently on 2365 level3 I am currently stuck on question 10 and needed some guidance. I have filled in what I could not sure if it is correct.
  18. J

    project Peugeot 308 Rear Window Regulator. Worked out 4 connesctions

    project Peugeot 308 Rear Window Regulator. Worked out 4 connesctions + - up down . But hesitates going up every inch or so? Any ideas please
  19. R

    2365 305 Project

    Hi guys, I'm working on my project, doing okay but run into the occasional roadblock and have decided to use this thread to hopefully get assistance. Will post problems as they arise.
  20. T

    Need help matching power supply to LED project.

    Hello, I am an artist in Portland Oregon and I need to power an array of 3 watt cob leds (9-12vdc 260-280ma) https://www.ebay.com/itm/311651957952 They need to be strung in strands of 8 (12 total strands) 96 total leds. I would like to run them a little underpowered to reduce the heat and...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top