Hi Guys,
Just a quick one,
I recently completed an EICR, the MCBS were push in wylex 3871 with a breaking capacity of 1 or2 kA depending on the size. The property's PFC was 3 kA so I graded it as C2.
My question is can I put in push in 60898 MCB's with a Breaking capacity of 6ka and put the...
Hi,
I am going to be making abour 60 cuts of 70mm tri rated cable, and probably many hundred more of the same.
Whats the best way to cut it without knackering it up?
Do I need a pair of ratchet cutters?
Clarifiation please !
I have read somewhere, maybe in BS7671 or on a forum site regulation that states that 16mm meter tails can or should be used on supplies rated at 80amps or under and 25mm tails on supplies rated at 100amps.
I have scoured BS7671 and various forums but cannot find this...
anyone herd or no what these web sites are called were the customer puts on the work they need doing and a price there prepared to pay and the apparently sparks quote etc new one on me
Hi,
I was looking at the MK switches as we wanted
them to match with the sockets.
But they only have a 32A switch which
matches, the 50A switch is quite large.
Will the 32A switch be ok for this induction hob?
Rated people
£500 job costs £4.30 +vat to quote in general maintenance (not electrical) section .
£500 job costs £14.70 +vat to quote in lighting and power section.
Seems a tad unfair lol?
Hi all,
I’m completely new to any kind of electrical work and would be grateful if you guys could confirm my setup to be correct.
I’ll try to be as clear as I can:
I have 220V coming from my Wall Socket, so I assume I have 220V to use.
What I’d like to do is, use the...
Due to the conditions at this job,working in a new shelf life room in a commercial setting I'm after some ip rated click roses.
basisaly I'm going to wire the then via conduit on the wall to a click rose and then cables individually to each light fitting(yes the fittings are ip rated)...
I need to switch 2No 3kW heaters on using a 7 day heating programmer. Presumably I'll need a contactor to switch that load rather than the heating programmer (?).
Can anyone recommend a suitable one? Many thanks if anyone can help,
Peter
So I was first fixing a bathroom yesterday and the plumber chap has drilled the holes in the ceiling - when I looked up one of the holes I could see that the hole cutter had "kissed" one joist and had just missed another (the house has had a loft conversion hence why the 2nd joist is so close to...
Evening all,
Could anyone offer any advice with regard to the following:
I am currently on a job in which a mezzanine floor has been installed with a suspended ceiling underneath. When I quoted for this job I simply priced to fit standard 600 x 600 recessed fluorescent fittings or LED panels...
Hi , quick question , in my thoughts requires a quick answer
160amp fused switch feeding existing Hagar panel board fine no problem with that
My superior wants to install a new 125amp rated DB fed from same switch ?
I don't I would want to see a board rated at 160amp or above
Thoughts please
Looked at job for a builder to put down lights in soffit of a porch, single storey flat roof 2m x 2m. But void is only 80mm deep, told him he should have built it bigger but just says put them down lights in with no covers. My I dea was fireproof down lights, but not enough room. So as its...
Hi all, i have a question. I have 2 small strip lights (not sure on the actual size maybe T4 or T5?) and I want to wire them to a plug socket so I can move them and I also want them both to be wired off the same switch.
I have done a quick drawing of how I plan to wire them but I am not an...
Hi been looking on old posts and one states Fire rated only required if another dwelling is above IE not same property or you break fire barrier in garage ?
i went to property 3 years old! and everywhere was mains gu10 non fire rated no fire hoods Its just a 2 storey house but would this comply...
Hi,
I have got to split some more tails etc and pop a mini consumer unit in someone's meter cupboard.
I always put IP rated consumer units in, you know, just 2 way etc.
Is it really necessary or would you say putting a normal metal clad unit it would be ok? Its just this time I have got to...
There's an item on the One Show at the moment about Rated people and how their ratings aren't always what they seem.
It's nearly finished now, but you can still watch it on iplayer.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc