settings | Page 2

settings

Recent contents View information Top users
  1. Gavin John Hyde

    KT64Dl changing settings from hidden menu

    I have come across a little menu on a KT64Dl and it may work on a 65Dl aswell. Put your tester in Loop, then turn on, as soon as the little red light goes out press F1 twice really quickly, a hidden menu then comes up which lets you add or take away values, so if you have say a 1 ohm source...
  2. gazdkw82

    Torque screwdriver settings

    I'm thinking of getting a torque screwdriver but unsure if it's worth it. Is it a regulation now or just good practice now for connections to be torqued? If so is it just for CU's?
  3. O

    BT Email and BT Spam filter

    This is a bit of a long shot but can anyone give me a clue as to the "workings" of the BT spam filter? We have 4 BT accounts - 1 each plus a generic family one. Yesterday I forwarded an email from the generic one to my son ..... it didn't arrive. It wasn't in his spam filter. So I logged on to...
  4. B

    Forum clock

    @ Dan Is there a forum clock anywhere? I can see my posts are minutes old then eventually a time . I believe I have the settings correct to autocorrect the clocks going back (and forward next year) I expect loads have the settings wrong tho as its hard to check (or is it and I am missing...
  5. N

    Thermostat timer settings

    I have inherited a fully working underfloor heating system, but can't work out the instructions for the timer that controls the thermostat! http://www.swegonhomesolutions.dk/Global/PDFs%20Archive/Air%20handling%20units/Compact%20Air%20(-2007)/_en/CACZ05.pdf I followed the instructions...
  6. P

    DOL settings

    Hi all currently doing my AM2 and stuck with the settings for the DOL, I cant remember for the life of me how to work out what setting to use, been over my notes and nothing. Any help, the motor is a 0.37kw motor 3 phase Cheers
  7. S

    Humidity settings on fan

    Hello Just wanting to know what % Humidity people tend to leave on bathroom fan settings? Cheers :)
  8. S

    Evershine 3000TL G59/2 settings

    Has anyone here had experience of changing the G83/1 setting to G59/2 on the Evershine 3000TL. Single button model. Midsummer have forwarded a pdf but it is at odds with the installation manual which says it must be done via the usb port and easy config (only available to service engineers)
  9. Pete999

    Help with settings

    How do I undo "mark as read"? sorry for the daft question
  10. S

    stop filling up my email account

    Hi how do I stop this forum sending everything to my email, computers not my thing cheers
  11. L

    Advice needed for configuring alarm system to make it pet friendly!

    Hi, can anyone give me some advice into configuring my home alarm system to make it pet friendly? I have an ADE Accentra+ user panel and Honeywell G4 fitted last November, i'm now looking into acquiring a pet and want some help about how to configure the PIR settings to make them pet friendly...
  12. H

    What Settings to Use on The EasyPAT 1600

    Hi, I've just brought a new tester a Martindale EasyPAT 1600. I want to know what setting to use on the items I test. I know the 100mA is for IT equipment, the 25A would be for the 13A fused items and 110v items. So would the 8A be used for the 3A, 5A and 10A items? And yes I have read the manual.
  13. S

    LP722 Turning on on Advance Settings Automatically

    Hi, I have replaced Tempus 7 wuth a LP722 Programmer fitted to a back boiler - (supposedly thats gravity fed - I do not have much knowledge about electrical/Boiler stuff). LP722 is set to turn on three times a day which is fine but it turns on automatically on 'Advance' sometimes - I think...
  14. K

    Torque Settings for Brass connections

    Does anybody know where I can find generic torque settings for M16 brass connection. We are connecting to a Weg motor. Have tried the manufactures but had no reply yet, we have two guys waiting to connect.... Cheers
  15. C

    SMA 3000TL settings will not save

    Hi guys, I am wanting to change my voltage to start feed in from 150v to 125v but when i set it to 125 and save it and go into one of the other inverters and change that and go back again it changes back to 150v every time, what am i doing wrong is the something that im missing ? Also i was...
  16. G

    g59 settings on SMA tripower inverters

    We recently installed a couple of tripower inverters that need to be set to G59 protection settings. Unfortunately they got set to G83 using the dials (5-8-2), which I didn't think would be too much of a problem as I'd picked up on it within a few hours of it being set. However, I couldn't find...
  17. G

    help needed with dno

    Help needed witj dno installed 3.9kw system with sma 3600tl which limits output bang on 16a max but dno says this is g59 as panels are over 3680 w is this right what they are doing?
  18. P

    SMA G59/2 Protection Settings

    Has anyone else noticed that the G59/2 protection settings of the SMA STP inverters have changed recently. For example the upper limit AC voltage was 253/264.5 V but it is now 264/276 V. I assume it is adding 10% onto 240V as opposed to 230V. This has been taken from the factory settings cert...
  19. S

    Single axis tracker settings

    We have built a single axis (manual) tracker system with single rows of panels. We plan to move the horizontal axis four times per year between 30 - 60 degrees. Has anyone done this and have figures for the optimum times/angles please? What expected increase in production can we expect? Total...
  20. M

    Schedule of protection settings on G83/1form (UK power network form)

    On the UK power networks G83/1 notification form, in the section information to be included, where it asks for- Computer print out (where possible)or other schedule of protection settings what do you include? is it just a link to the inverters manufacturers website or ? and Electricity...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top