settings | Page 3

settings

Recent contents View information Top users
  1. O

    testing equipment with electronics inside plus

    Guys as more and more equipment have got electronic or computerised equipment fitted ie a washing machine used to have a elctromechanical dial now they have on board electronic / software control so my question is how do you approuch this with regards to the type of test ie test with 500vdc or...
  2. B

    SMA SB4000TL Country Settings

    Hi All, Had a PV system installed today - 16 x 250w Sanyo panels (have had DNO permission to go over 3.68kw) and a SMA SB4000TL, so what settings should the inverter be set at - the installer has set it at 0 and 1 - but I have read somewhere that it should be set at 5 and 8, is that correct? In...
  3. S

    Battery powered golf trolley.

    I am flogging my battery powered golf trolley. It has twin 250w drive motors, brand new (year old) 33ah battery goes for miles. It is remote control but i have never had a remote for it. It is as quick as fcuk has 4 speed settings and i cant keep up on any higher than speed 2, anti wheelie bar...
  4. W

    veritas r8plus alarm

    how can i find out the engineer code for this alarm system ( already fitted when i bought the house). i need to reprogram some of the settings and the user code does not work for programming. the default engineer factory code..1234 has clearly been changed so also does not work, or do i need an...
  5. J

    Measuring earth loop imopedance Ze using FLUKE meter - settings??

    Guys (n' girls of course) I have just started using a 1653B FLUKE and when testing earth loop impedance Ze (ie. impedance of supply - tested at supply origin), I presume I use the 'LOOP IMPEDANCE' setting (line to protective Earth L-PE) using the Z1 Hi current setting, and NOT the 'Earth...
  6. C

    inverter protection settings

    hi again sorry to be a pain but we`ve just installed a mastervolt xs2000 on our first install and i can`t find any of the inverter protection settings. any ideas guys they`re probably staring me in the face but i`m getting battered with paperwork!!!!! as you all know! thanks col
  7. W

    Inverter protection settings

    Hi, short and sweet Can someone tell me how to access the protection settings on the sma 3000tl inverters? TIA
  8. M

    Protection Settings?

    Just wondering what protection settings you have been including for displaying next to the inverter. I've looked at the DTI guide but i'm not too sure what to put from the inverter manual. Any help would be much appreicated. Thanks, Mark.
  9. M

    Inverter protection settings

    Hi I must be having a senior moment here, but I'm trying to find the protection settings for my SunnyBoy 3000HF. I can't seem to find it in the manual or datasheet. Can anyone point me in the right direction? Thanks in advance!
  10. S

    Lighting with two power settings - without using preset dimmer?

    Trying to google a product that can do this - but struggling to describe it! Has anyone come across a switch that allows lights to be fully on in one position, very low - for night time use in a second position - and completely off in a third - and without resorting to a preset dimmer...
  11. A

    need help on what settings to put in a D.O.S starter for a 0.65Kw three phase motor

    if i have got a 0.65Kw three phase motor does anybody know what i need to change thew settings to in the D.O.S starter??
  12. D

    "Protection settings have been set to comply with Engineering Recommendation G83/1"

    Hi all, In our DNO notification form it asks for confirmation that, for the inverter: "Protection settings have been set to comply with Engineering Recommendation G83/1." & "The protection settings are protected from alteration.(except by prior written agreement between the DNO and the...
  13. S

    Small PLC's or Logic Relays used in Domestic/Commercial Settings

    Hello All I am looking for peoples experience of using small PLC's or Logic Relays in the domestic setting. I am looking at the likes of the moeller easy, mitsubishi alpha, and the likes. I have only used one of these types of relay in an industrial application over ten years ago and this was...
  14. N

    Ze/Zs differ (wildly) between no-trip and 'regular' settings on Fluke

    Hi, A puzzling issue today. When I test for Ze and Zs on my Fluke I tend to go for the 'no trip' setting out of habit. I believe whether there's a RCD or not this test might take a little longer to get the reading (as it saturates the RCD with a DC current) but it's the same result as the...
  15. Golden_Boy

    CM500 printer settings?

    Anyone know the setings for a serial printer when used with a megger cm500 MFT? Baud rate,stop bits,parity etc. Cant find the info anywhere.... the handbook just mentions An " appropriate" printer.:confused:
  16. M

    Request:-Motor protection settings for LT 110KW Motor

    Anyone,pl. give me settings for 110kw Lt Motor for Siemens make7SJ62 relay. Thanks ,
  17. E

    please explain relay settings

    We are using 10 MVA 110/11 kv Transformer for 6 MW power plant. The transformer relay setting has given (7sj621 siprotech siemens multifunctional relay) CT ratio 75 / 1 A Relay code settings 51 Ip> 0.8 Ip>> 13 What is the original tripping value and how did we calculate it...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top