hi there,
im about to open my own shop. there is currently alot of lighting cable that runs down through a suspended ceiling. i am pulling the ceiling down and putting up a new plaster board ceiling. i have a qualified electrician who has been in to look at switch boards current wiring etc. We...
Hello guys I'm a newbie so go easy on me
I have a job to do which I quickly had a look at today but didn't have time to complete the question is
I have a about 15 lights ( 2x14w t5 ) and they are wired through eachother in a plug and socket arrangement for example Plugged in either side...
Hi
I put a light (5ft high frequency weatherproof batton) in a kebab shop last week
It was approx 2 metre away from the kebab machine that gets very hot, approx 200 degrees.
The light worked fine for 2 hours then it just stopped working. Changed the bulbs and still nothing working. Checked...
Hi,
I was wondering if anyone would know what the acceptable minimum and maximum on a single/three phase main incoming voltage should be. From what I have gathered you have a tolerance of +10 230V -6. Could you also quote from where it is mentioned in the wiring regs.
Thanks.
OK, commercial shop, no rcd protection on sockets, surface cabling in trunking. Wants 2 x 2g sockets for office and 1 x 2g socket for "fixed" display of product.
Do these need to be RCD or not.
My common sense approach says the one for the display should be but the office not.
Tin hat on!
Hi
I have been given an opportunity that is too good to miss! its on a busy road, about 10min from town center really but theres not much around it other than HOUSES and pizza shop..
It is a fairly average size shop with a working kitchen, and a flat upstairs been offered it for 300 / month...
I have been asked to replace the bulbs for a Coral Bookers, shop sign, when I opened it up I found LEDs in Series, any idea where I can get replacement LEDs for these signs from?
The other option would be replace the whole sign which I they dont want to do unless they have to.
Hi guys I do not do much comercial work but have been asked by some one to do a EICR for a shop I know what the going rate is for domestic but how much do you charge for a shop. I know Iam short on details here job is in west midlands.
any help on how to price would great.
A young girl started work in the village chemist shop.
She was very shy about having to sell condoms to the public.
The owner was going on holiday for a couple of days and asked if she would be willing to run the shop on her own.
She had to confide in him her worries about selling the...
We've just been asked to install a shower to a back room in a shop to wash dogs...
It's a pooche parlour!
The room has 3 double sockets one located about a foot from the doggy bath/ shower area.
All circuits are RCD protected and we're gonna blank off the closest socket.
Not sure on the...
been out of sparking for a while hence the question , we are opening a shop and have some fittings but no lamps yet! so questions are , can these led lamps be wired in series loop in and out on ceiling tiles ,and do i need a resistor somewhere what are pros and cons 230 vs 12 cost wise , ease...
Hi Guys, i am an english electrical contractor, and have been asked to quote for some works in a shop in Paris.
Any body had any experience on non domestic wiring?
who do i get to certify the works?
will it need certifying if i don't install new circuits?
any help / info would be appreciated.
Ant.
Hi Forum-ers,
I was hoping someone can help me, as I'm stepping out my normal line of work to help a friend.
I'm an electrical fault finder on the railway, but previously did some industrial work and so have BS 2391.
My friend is installing a small kitchen in a shop, the shop fitter has handed...
Hi all. I've been asked to design and install the lighting for a sandwich/cheese shop. Looking around on the net the recommended lux level for a Deli is 500lux. Does anyone know how many mod fittings (4x18w) it would need to achieve this in a room 7250x7500 and about 2500 to the ceiling. I've...
hi all, not sure if im in the right bit here but....need some advice im wiring in 2 sunbeds (250w) for a shop thats being converted into a salon.
due to the load im assuming each sunbed needs to be on its own circuit with breaker, will 40a suffice? with a 100 ma rcd?
as for the cable, 10 mm...
Just An Idea,
How about with things the way they are, We start a swap shop,
For Instance I have 4x Suntech 245's monos Knocking around, would be willing to trade for Sharps 245 for Instance. Il name my price for suntechs you name yours for sharps etc,
Not just Modules but fixings, Inverters...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc