shop

  1. G

    Rcbo`s for tv shop?

    Hello everyone new electrician signing on. Have a small query? I have to do some alterations to a small tv shop soon. I have no info at all yet about the installation as yet. I am just getting info in my head together before i get on site. Being a small commercial site, i am presuming it will...
  2. L

    Advice needed on sweet shop wiring!

    Guys I've been asked to quote for a new ccu and rewire of a small sweet shop with store room, the main shop is about 8m by 5m and store room is 3m square, it's single phase 60A service fuse. I've been given a brief layout diagram it will be 1 power circuit for each side of the shop and one...
    • LlandrilloSpark
    • Thread
    • advice aus needed shop wiring
    • Replies: 2
    • Forum: Australia
  3. R

    Roof rack shop in surrey/hampshire?

    I need to try and get a roof rack or bars for my van by the end of the weekend. Obviously there's plenty of places to buy online but none promise very fast delivery Does anyone know if there's a shop in the surrey / hampshire area where i could walk in and by one??
  4. R

    Flat above shop, CU in shop PIR

    Had a look at a possible PIR on a flat above a shop.... unfortunately the CU and meter etc for the flat is in a shop, and when the shop is closed at night, there is no way to get to the CU from the flat, and no way to isolate the installation. What would this be on a PIR? I'm thinking it's a...
  5. M

    Small Shop- CU change

    hi all, doing a consumer unit change in a small shop only has 4 circuits. did a PIR first, all circuits are good. problem is that I cant find a small consumer unit that is dual rcd. I understand the whole installation can not be protected by one RCD. Is RCBOs the only solution? It boosts...
  6. E

    Shop

    The shop I'm about to do needs a new rcb Board etc. What i need to know is can i use low voltage lighting........... ie:them on wires ? Smoke alarms ''''''''''''''''''''''''''' Do i need them too ? Gas Mtr pulled out and no gas in the building, pipe still in place. Does this need 10mm...
  7. E

    Shop rcd's

    Does a shop have to have rcd's or can it run on normal protection ?
  8. O

    lighting display for shop

    Hello, new to this site and already found it to be a wealth of information. Now i need some help, have just been asked if i can set-up a lighting rig to display different lights on, prior to sale, (same sort of idea as B&Q, Homebase). was thinking there might be a track system with...
  9. E

    Wiring a small hairdressors shop - what are requirements for RCD Protection ?

    Hi , Looking at the possibility of doing a rewire in a small hairdressing shop and wondered what are the requirements for RCD protection ? The requirements would simply be for sockets , lighting (probably functional and decorative) , water heater e.t.c. How do the regs alter when moving...
  10. K

    illuminated shop sign

    i have been asked to have a look at an illuminated shop sign, as it looks like some of the tubes have stopped working in it. anyone know how these signs come off how you get access to the tubes??? is the a nack to getting them off etc?? dont want to look a fool trying to get the cover or...
  11. P

    domestic installer rewire mates shop

    A bit of advice please, my mate has asked me to rewire his shop its a old terace house turned into a shop. i'm a niceic domestic installer, am i right in thinking i can do the job as long as i go through the council planing route, is it LBC. Any advice would be great Thanks pete :confused:
    • petewan
    • Thread
    • advice aus certs commercial domestic domestic installer house installer mates rewire shop thinking
    • Replies: 12
    • Forum: Domestic Electrician Forum
  12. P

    tt supply to work shop

    Guys, looked into a tt system today and found at main board which is rcd protected a 10mm armoured going to a board which is in the workshop then feeding circuits in there. The board in the workshop has a earth rod in the ground however the supply to the workshop from the board in the house...
  13. C

    Shop sign lighting

    hi i have been asked to try and fix some sign writing on a freinds shop.there is a feed in to the light and a feed out both with 230 v. from the incoming 230v its goes to a capaciter then to 2 ballasts then to the tubes. he as tried new tubes and starters but still no joy. i would think it...
    • chopper
    • Thread
    • aus lighting shop sign
    • Replies: 9
    • Forum: Australia
  14. N

    3 phase socket in a shop

    Hi Guys I have been asked to price a job in a sun bed shop, the work would include adding a 3 phase + N DB and running 4 supplies to the new beds using SWA cable. My questions are as follows. 1. Is it ok to install a 3 phase + N supply in a shop where the general public have access...
  15. S

    New Shop Supply

    Evening all, Along with the TV shop refurb, im also in the process of a new installation in a kitchen showroom. Anyways, long story short, the DNO came in to install, what i thought would be a 3 phase supply. but apparently (unknown to me) have installed a single phase 3 wire. Any...
  16. M

    IR test on shop best way to test

    I have to test shop today but it not possible to disconect every light fitting (1200 * 600 fittings)and other ones with electronic ballists . Also i can not get in to disconnect the tillsand other sockets what do you think the best way to tes the IR on this
  17. S

    TV Shop Refurb.

    Well chaps, today was the first day of tidying up this little lot. Loads of Wylex rewireables, big green enclosure is the contactor to shut off all the sockets via switch on the way out of the workshop. Dis assembled the cupboard as the new DB wouldnt fit:D 8am start:( Then remove the...
    • Spudnik
    • Thread
    • aus shop
    • Replies: 2
    • Forum: Australia
  18. N

    refurb on a shop with a flats above

    Doing a refurb on a shop with a flats above it. The customer has had a suspended fire rated ceiling fitted under the existing ceiling in the shop. At present the shop lights circuit starts in the basement then goes straight up though the shop and in to the floor of the flat above where it...
  19. M

    Shop refurb into a sunbed shop.

    Hi are their specific electrical, fire alarm and emergency lighting requirements for a sunbed shop. I know that there are certain basic electrical requirements but will I have to wait and see what building control specify and also the fire officer ? I have done a few search's on the web but...
  20. S

    new shop in leeds

    hi everyone, just been too look at a nice job in leeds which should give me plenty of work :) shop is approx 15m x 35m ish with a mezanine floor at one end. couple of questions as ive done a bit bit not that much comemrcial stuff. 1. there are going to be a max of 12 refrigerators, do i...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Back
Top