Went to a job in a church hall today where one of the power circuits was tripping the rcd. There seems to be 4 bad legs of pyro in the circuit, as I get a dead short in my IR tests between line/neutral, line/earth.
Is it common for pyro cable to do this after a certain time, or could a fault...
I am happy with calculating current carrying capacity for straight runs of cable. I am not to sure how the imact of a ring effects the cable calcs? Its hard to see what the possible loads might be. As of this do you take the center point and use maximum demand?
So for example on a 35 meter ring...
my rcd 30ma trips everytime i put the iron on, it lasts a couple of minutes then trips , all sockets and lighting trip ,so its a big inconveinience,, any advice would be a great help. thanx,
bmc48
Thread
circuits
leakage
problem
rcd
replacement
short
trips
Can a motor overheat and short to earth if it is having to work to hard?There is no overload but the motor is protected by thermistors and a thermistor relay which cuts out on occasions. Its an intermittent fault but the Engineers that have watched the circuit say it trips the Main C/B. On a...
MatthewC
Thread
earth
heating
motor
motors
overheating
protection
short
Hi
Can anyone tell me where I can get one of those little fuse thingies that goes inside a 13 amp plug top??
I want an 8 amp one.
Thanks for your help. :)
Hi All- New to this - loving the challenges!
EICR'd my house and found one of my ring finals had an IR problem- just getting to grips with testing and trying to gain experience- college was good, however, felt like it was more of learning to pass exams!
My ring final has an issue- if i test...
Just had a call off my electrician (one doing council work)
He did a CU change - on testing he IR tested the lighting circuit (500v DC) and got acceptable readings.
When he energized the circuit - RCD trips. Found a dead short between N and E. Investigating now to locate which run of...
HI Can anyone help me understand how I work out the "short circuit capacity(KA)" for Domestic Electrical Installation Certificate. Sorry struggling with this one.:blush5:
atko
Thread
capacity
circuit
front
looking
product
shortshort circuit
when doing an inspection i came accross a radial circuit serving 4 points, the IR between L-N @500V was 0.00 Mohms, on continuity between L-N I got 25 ohms. when I then energised the circuit and clamped the live, no current being drawn. I have yet to take any fronts off as it was just an...
Do you guys think that the majority of electricians actually bother using the adiabatic equation to decide whether the cpc of a T&E cable is adequate when supplying a CU in a garage/shed, or do most people just size the cable based on CCC and voltdrop?
I come across a lot of T&E strung between...
Hi im looking for a list of Circuit Breaker short circuit capacity ratings, that i can stick into my BGB.
list required would be for all fuse types, from BS 3036 to BS88. old and new types protective devices.
Also is there such a thing as fuse wire sizes gauge card? if so can some one point me...
Hi to you all,
My name is Colin and I am a middle aged sparkie going down the grumpy old man route after looking at the state of our profession (Middle age is when a narrow waist and a broad mind always seem to exchange positions!!). I spent 8 years learning the job and the last 18 years taking...
Firstly, please let me explain the fault on the circuit HAS been rectified. This was achieved by splitting the offending circuit (kitchen ring) into two radials and putting each leg on their own 16A mcb on the same RCD.
Attended a property to do some remedial works on the kitchen ring, New...
Looked at a job today where the elderly occupants have the old rewirable fusebox tucked away high in a kitchen cupboard where neither of them can reach, or replace the fiddly fuse wire.
They've asked me to price up replacing the CU with a split RCD unit but would also like it lowering so they...
The prospective short-circuit current between line and neutral is measured at 900A. The maximum balanced prospective short-circuit current level between lines, as a rule of thumb, can be assumed to be approximately:
A: 0.9 kA
B: 9 kA
C: 90 kA
D: 1.8 kA
:banghead:
Check out the pics above; this was a callout to lost power in a factory, found 2 phases out blown 200amp fuses and a quick Meggar confirmed a short circuit between Y and B phases and unusual low readings to earth. id already isolated all outgoings and main switch was off to busbars but still...
We've been to Centre Parcs on and off for a number of years and yes, as a family we do enjoy it but its not cheap.
Looking for suggestions of places "like" Centre Parcs in the midlands/south which would have similar type offerings.
Thanks.
Hi all
Any of you know whether there is a table or other source (other than waiting on hold for ages or opening the fuse covers)to find the short circuit capacity for a 200A main fuse in a 3 phase 40 year old supply?
Also is it going to be BS88 or 1361?
I'm planning on installing the mechanical side of a PV array before I install the electrical components and I've heard that you can connect the positive and negative leads of each module together to short-circuit each module separately until you string them together. Is this true or would it...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc