I have installed a number of 120v smart light switches and smart bulbs which I have set up on a schedule via an app. I would like to add another smart light switch for a light fixture that has a 120v to 12v transformer inside the light fixture, lighting six 12v (previously halogen) currently LED...
I am organising a switchboard upgrade to my property and have recently had a smart meter installed.
I am receiving conflicting information regarding whether the meter provider will need to also come out on the same day as the electricians to re-install the smart meter after the new switchboard...
Hello. I’m trying to hardwire a smart doorbell but have no idea how to bypass the existing bell chime (the new doorbell has its own chime box plugged in elsewhere). I’ve attached a photo of the component in the existing bell chime. At the doorbell itself there is one of both the orange and blue...
Hi everyone, my house has an air-to-heat system that generates hot water in a boiler. This boiler is then connected to the central heating radiators and we've got two thermostats (one on each floor). This is a new build.
I'm considering installing a smart thermostat and smart radiator valve...
Hey guys!
New DIY 'new build' homeowner trying to not cause any damage to wiring!
I'm looking to swap out the existing traditional light switch with a 3 gang smart switch in my kitchen. I've successfully managed to wire in two 2 gang smart switches in the bathrooms but this 3 gang switch has...
Ok guys, first post so be gentle. I have a standard setup of two two way switches, one at the bottom of the stairs and one at the top so the light that they feed can be switched on/off from either switch.
What I want to do is replace these switches with smart switches. I have installed one...
Hey all,
Currently I have two wall switches that control two outdoor spotlights.
I Want to install smart wall switches.
Some require a neutral wire (Wyze, kasa, etc), a few don't (much more $)
Does this box current have neutral wires or no. Thank you in advance!
I am replacing a 2 way switch with a smart switch. The old switch has three sockets - common, L1 and L2. I can see where the wire that went into 'common' goes on the new switch, hit the new one also has 'P' and 'L' instead of L1 and L2 - which wire goes where?
Hi Everyone, DIY advise required here please.
I have the following wall switch, currently wired in as below and controlling external roller blinds.
Inside the wall view has additional wires.
My DIY project is to replace the wall switch with a smart one below
And here is my wiring...
Please can anyone recommend a smart dimmer module for use with Aurora LED GU10s that remembers the dim setting on loss of power so that the lights don't come back on full brightness (or, even worse, remain off) when power is restored? Ideally Wi-Fi controlled. There isn't sufficient space in the...
Good Evening Everyone
Was looking to replace both my old Danfoss mechanical thermostats with a smart thermostat. Was wondering if anyone had recommendations for the following set-up (circuit is 240v).
There are 2 solenoids, one for upstairs and one for downstairs, and a thermostat each for...
Disclaimer: Not a pro sparky, so i have no intention of doing this myself, but I am looking for options that I can then take to someone qualified.
I am looking to replace the consumer unit in our house for a number of reasons, and its location means that it is directly visible by anyone coming...
I have outdoor lights that are controlled by dusk sensor and then timer (for OFF) on the right of the picture. The switch to the left of the box powers off the entire fusbox therefore I cannot change that as I have other things I keep on). What do I need to buy (switch/plug?) to swap the old...
Hello! I'm installing an Aqara smart light switch (with neutral) but nothing is powering on after getting everything wired up. I've attached pictures of the original switch (working) and the smart switch (not working). I've confirmed power was restored at the panel and voltage tester confirms...
Hey
So I'll say I'm not a qualified sparky however I know how to wire up a replacement socket or a replacement dimmer (but I couldn't add a new one)
I'm looking at Lightwave products for smart sockets with energy monitoring. Are these any good good? Would I perhaps need anything in addition...
Trying to install a smart thermostat,
I have 4 wires red, yellow, blue and earth,
And this smart meter wiring diagram baffles me.
1st photo old thermostat,
Hello, I am on Economy 7 and I have storage heaters and a hot water tank connected to a separate CU for my off-peak usage. The timer that switches to the off-peak circuit at night on my newly installed SMETS2 smart meter is wrong so I am being overcharged by 50% for my night appliances. The...
DIY Advice required. Ive just recently brought a Sonoff T0UK1C wifi smart switch for my Living Room. The existing light switch is ya standard one way switch with live/neutral connected (No earth wire connection - therefore earth is isolated). How would I wire the Sonoff switch in replacement of...
Hi DIYer here. I replaced a one gang switch with a no neutral smart switch. I put the provided capacitor between live and neutral in the ceiling rose. All seems fine except that occasionally the light flashes when one of the other switches on the loop is switched on. Is there anything I can do...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc