stand | Page 3

stand

Recent contents View information Top users
  1. 5

    Generator

    Can anyone offer any advice on what to look out for when buying a second hand generator that I intend to buy to supply a house in Spain. Like how do you load test or if a generator gives the power it states on the label. Cheers
  2. R

    Can someone look at my City & Guilds certificates and tell me where i stand please?

    Hi Fellas, i would like someone to have a quick look at these and tell me where i stand. I finished the first year NVQ lv 2 I got to the end of the second year NVq lv 3 but never completed the AM2 test. Did around 2500 hours at college in those 2 years Got my 16 and 17th edition I'm...
  3. T

    where do I stand....

    here goes the cupboard where my DB is is a disgrace to be honest it's not going to kill anyone but i can no longer put up with it! (not done by me BTW) So it's coming out and I'll re do it as I see fit No offence to anyone that does domestic installs but it's just not me I don't do them, but i'm...
  4. M

    trade stand

    Hi Anybody been to a exibition / show type of thing to sell their services Ive just booked one so any pics of what you may have done just looking for ideas. Cheers Mayfair
  5. R

    what does the AX stand for on light switches?

    The A is obviously amps, but whats the X?
  6. P

    Wiring Lighting Circuit

    Hi there, was in the wholesalers today and got chatting to the staff and was told that apparently the NICEIC want you to send the feeds to the switches, neutrals together etc, oppose to three bar wiring (loop in) Anyone else heard this,?
  7. B

    Where do I stand with this one?

    I was asked today to install an extractor fan in a bathroom So I was going to take a feed off of the lighting circuit The fan i am installing does not require a cpc however the lighting circuit in the property does not have a cpc anyway Can i still install the fan or do i need to make sure...
  8. J

    Advice on stand alone P.V. system upgrade please ...

    Hello All , By stand alone I mean off grid -domestic I have a few questions about where to go now with this situation -I have an existing System that doesn't have quite enough juice so i will be enlarging the existing capacity. so I have bought some kit which I can't take back so therefore will...
  9. N

    Where do I stand on my quals?

    First post after a few days reading and I figure it just easier to ask the question. I did a BTEC ONC in electrical and electronic engineering in the army. On an upgraders course I also completed a number of higher modules and should have completed my advanced modern apprenticeship. I never...
  10. G

    where do i stand?

    at my place of work we have been having meetings over a 12 month period as regards redundancies, anyway about 8 weeks ago i got a letter stating i would be made redundant on July 27th, today i have been informed it is going to be on a week to week basis - is this legal? i have worked for the...
  11. B

    Stand my ground?

    Ok so i'm currently working for an agency who have put me on this job which is quiet a good job with the prospect of a good 12 months work found myself in a dilemma today though We are upgrading the bonding, in fact introducing bonding cos there was none in this factory But that is besides...
  12. K

    Stand alone system

    Hi guys I'm just wondering if anyone had deal with Stand alone systems? Basically for me it is not very clear what is classified as a "Stand Alone System"? I know in other contries the Stand Alone Systems refer to Off Grid Systems, but in the UK everything must be a little complicated. Here...
  13. Amp David

    Ring testing when stand alone RCD is used.

    Working on a RFC today and its had a stand alone RCD added previously which is installed outside of the 3036 fuse board. When testing ring continuity and R1R2 would taking the conductors out of the RCD then joining them be the prefered method or taking 2 readings, one from the fuse board to the...
  14. S

    Planning for Stand Alone Systems

    Stand-alone Solar Panels: The following limits apply to stand-alone solar panels: They should be no higher than four metres; They should be at least 5m from boundaries; The surface area of the solar panels forming part of the stand-alone solar is limited to 9 sq m (or 3m wide and 3m deep)...
  15. SolarCity

    FITS review - stand alone systems

    Just been scanning through my early morning reading material and came across an article in Roofing Today about the FITs review. In this article, it claims that Stand Alone Systems will only receive 9p per kWh after August 2011. Surely this is incorrect as I've not heard anything about this...
  16. E

    problem with tns system, where does the customer stand??

    did a job the other week and on completion found earth was taken from lead water pipe . put in temp earth rod and advised customer to get energy provider to come have a look and sort it out. A week and a half later after we called them they said they will come and look but it sounds like they...
  17. C

    Whats PSC stand for and what is it?

    Just wondering what it is, iv'e looked online and cant find it. Cheers, John
  18. U

    old wylex board

    quick dilemma, bathroom fitter i work with just informed me that the quick rcbo changeover for a light in bathroom is an old metal wylex fuseboard in a cupboard for a flat. im pretty sure that u cannot get rcbo for these boards................i maybe wrong?..........it has the mcb conversion...
  19. P

    what type of certificate for a display stand

    Part 1 We have been asked to supply 6 sockets mounted on a board with a 20amp switch and fed via a 3 core flex & plug top, this is mounted in a display unit where the user can plug in laptops and other display items, we have to supply a certificate for this and i am unsure of which cert to...
  20. U

    stand alone rcd

    anybody reccomend any good stand alone rcd? have a cct board, no rcd protection, cant get rcbo for type of board as mentioned in previous post, need to protect 6A upstairs light cct as light has changed in bathroom.............a stand alone rcd was mentioned?! any pointers? cheers all for...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top