trouble

Recent contents Top users
  1. B

    tester trouble

    Helo I'm fairly new to this testing so perhaps someone could explain this My Fluke is giving off some quite varied readings. We we're doing some R1+R2 testing and when I tried to zero the leads it appeared to make no difference and then the circuit reading seemed to be going all over the...
  2. J

    Volt Drop trouble

    Hi ALL Have to install a Condenser unit on a roof in the nxt couple of weeks the length of run is around 50M the unit FLC is 24A will be Reference method E on Try for most of the run 4mm swa can take 41A table 4D4A and 6mm can take 53A. Just need some advice regarding VoltDrop As this is...
    • James Sutton
    • Thread
    • aus electricians' talk table trouble volt volt drop volts
    • Replies: 3
    • Forum: Australia
  3. J

    Busbar trouble

    Hello Have got an install coming up in a couple of weeks have to remove a 3phase 40Amp supply feeding a Condenser for a multi split AC Unit What will leave me with 3 spare ways on the board but we then putting in 6 units pulling around 10-12A FLC so was going to run 3 radial circuits then...
    • James Sutton
    • Thread
    • aus busbar electricians' talk trouble
    • Replies: 3
    • Forum: Australia
  4. T

    rcd x5 testing trouble

    i have been testing an rcd with my calibrated tester but when i test the rcd on x5 my meter shows an error message stating that the fault voltage is greater than 50v. I thought it might be my meter so tryed another and it worked fine. I am now wondering if his meter is faulty.Any ideas?
  5. I

    Trouble Getting On The Site

    Has anyone experienced trouble accessing Electricans Forums over the weekend Chris
  6. S

    Trouble wiring 11pin 3pole solenoid....

    Can anyone help me? I'm trying to install a key isolated bathroom fan. The fan is in and working fine off the humidistat, I've then fitted a 3 pole solenoid controlled by a key switch. I've linked the key across pins 2 and 10 in accordance with the instructions, but it doesn't activate the...
    • silentboarder69
    • Thread
    • aus electricians' talk solenoid trouble wiring
    • Replies: 3
    • Forum: Australia
  7. D

    Motor Trouble

    Hi guys Got a question in regards to some automation hope you can help I was servicing a pick and place stacker crane last night and needed to replace a lenze MCA asynchronous servo motor that controls a set of telescopic forks. The said motor has a resolver for use with a lenze invert...
  8. E

    Double Trouble

    Whilst replacing an old DB I found that an outside light had been wired in and doubled up at the MCB, foolishly I had counted the the old fuses without taking the cover off, the new DB I had bought allowed for no more expansion can I double up at the MCB with this extra light, rings circuits I...
  9. D

    Dimmer trouble

    Hi I'm new to this forum stuff so be gentle. Can anyone tell me why when I put two dimmer switches on either end of a two way lighting circuit the lamps just flicker instead of illuminating as normal?
Best EV Chargers 2025
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

TrueNAS JBOD Storage Server

UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
JBOD Forums: a forum for JBOD storage server advice
JBOD Suppliers: JBOD Storage Server Supplies
Back
Top