Hi!
I'm using a cable with 2 poles and a shielding wire.
The cable should be soldered to a circuit board with + and -. But I'm wondering what to do with the shielding wire?
I've read that it should be connected to ground in one of the ends. But I'm wondering where and how to connect to ground...
Hi
I have a Transformer, that needs a rewire on a Secondary windings, the wire that was on it, was a muti-core wire 9 strands, (0.06mm x 9) ( each strand enameled ), soldered together at each end, and laid on top of the primary winding with 175 turns, with a copper tape between the primary and...
I've got an old furnace fan I kept the last time mine was replaced. I'd like to use it for various purposes. It has a red, black, yellow and orange wire. Also a purple going to/from I'm guessing a capacitor on the side and a green ground wire. Can I wire it up to be used on 110v ? I have...
Hi men. This fixture began flickering then the bulb died. I put a new one in and it immediate made a popping sound and died. I opened it to look at the connections and it appears the ground wire is disconnected. I don’t see the other end of the ground wire or anything that with my limited...
Hello, Thanks for reading. I want to make an improved version of the small solar powered dandelion lights you can purchase as I feel these are too small, and won't work very well in the UK winter months when its not very bright in the daytime.
However, I'm stuck on deciding what type of wire...
Hi all,
I am hoping someone could settle this for me.
I would like to know if it is possible to wire a 3 way switch, where the master switch is feeding 2 slave switches separately, i.e. rather than going Switch 1 > Intermediate Switch 2 > Switch 3, it goes Switch 1 > Switch 2, and Switch 1 >...
I am having some trouble with replacing a lighting fixture. I have done many throughout the house without issue, but this one is perplexing me. It is a light with two switches. When I took the light down, I was in a hurry but I swear both the black and white wires on the fixture were wired to...
Evening all
Try to rack my brain about whether this would work.....
Customer on a job wants to add a 3rd switch on a lighting circuit, however it is near impossible to get from the 2way switch but easy to get from the first switch
Will having the intermediate switch where the feed and switch...
Hi all, hoping everyone has enjoyed their bank holiday weekend. I hope this post goes in the right place as I've just joined. I'm looking to swap a two way light switch and two double plug sockets from bog standard plastic ones to stainless steel ones, the existing wiring (old colours) has an...
Had a kitchen unit with under light.
Took down one unit and I have capped the electric and taped. How can I cut back the wire so that it can be pushed back into wall?
What do I need to buy? Easy job to do?
I have accidentally cut a 16 mm earth wire running through my loft. It's in the middle of a 30 metre run. What's the approved/acceptable method of joining the cut ends?
I am not a electrician and I need some help. I would imagine this should be an easy one for you guys. I am trying to hook up an indoor air filter that hangs from the ceiling. I cannot find a schematic for connecting to a power source. It is a four wire system. I am not sure if it is a one speed...
I ran 10/2 wire from 30amp breaker installed on my house 100amp panel 50’ to my shed . I bought a sub panel as shown below ! Looks like to power the capable 2 breakers I should have ran 10/3 wire ! I am not in need of 220 v so Since the 10/2 is already there can I jump from black power line to...
I live in an apartment and would like to have a vanity light installed above a mirrored cabinet in the main bathroom. Any ideas how this might be done and at what cost? A handy man told me it would be a messy job as without overhead access he'd have to run a chase from the ceiling light down...
Hi guys!
I bought a pool heater online and this Is the wiring diagram that comes with It. Can someone please tell me if this Is possible? From what I understand the 3 wires from the heater must be spliced together with just 1 wire 127w from my main panel but the diagram reads 220v
Thanks for...
We've had a tiler in doing the kitchen floor and through no real fault of his own the floor flooded a little (stopcock issue). Was only surface water but its seemingly gotten around some wires.
Anyway, I came down and could instantly hear this electrical noise. Like a fuzz. Like something out...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc