I installed a doorbell where the button to activate it is 70 feet from the chime. I thought 14 gauge would be enough, but when I pressed the button, no chime. I realize what a mistake this was. I've attached a diagram showing the ridiculous distance in number 1. Would it make a difference if I...
8.5K shower unit is wired to plastic box consumer unit to 30 amp cartridge fuse with no RCD
It’s the original shower installed when the house was built around 1995
The shower is still fully working after all these years, never blowing the cartridge fuse before
Am I right to presume RCD wasn’t...
Hi all. Newbie here and hoping someone can help.
Some time ago I replaced the landing double light switch. Wires must have come loose as it stopped working. Put them back in what I thought was the right place but its not quite working properly. Its one of these thats connected to the one at the...
I built a prototype Dog Dryer. Took a dryer element and pushed it into a vent pipe. Cut out vent pipe to access the two spade connectors on the heater element. Attached pipe to blower (range exhaust blower). The blower is wired independently to 120V plug. Heater wired from an unused NEMA...
We do not have an outlet in the area behind the oven. Our current oven is hard wired.
There is an outlet just above the counter near the oven area. Can a new oven be plugged in that outlet?
Can any oven be hard wired if we choose to do that?
Is it easy to install an outlet behind an the...
I have an old hifi system that has a record player stacked on top of an amplifier. Weirdly, both are wired to the same plug. I don't know whether they came like this or whether somebody did it post purchase for some reason (I inherited it from my grandma). I want to pass the record player on so...
I'm having issues with the new Blink doorbell that I Installed today.
Basically, unless the doorbell is wired, it will default to a VERY basic use and run on batteries only which is not what I want.
It states that it needs to be between 16-24V and maximum of 40VA. Now I bought a bell...
Hello all.
For years now I've used Phillips Hue smart bulbs in my 3, ceiling mounted lounge lights and have therefore never needed to switch them individually.
I've recently redecorated and moved to a light fixture that cannot take Phillips Hue smart bulbs, so I have decided to go from a 3...
Hi,
Really just for info. not a problem or anything.
(to be honest also wanting to be sure it is taking from solar as much as possible & can you be sure of that?)
I assume the new solar meter is actually what is being drawn from the array so is an accurate indications of that.
Grid tied 4kw...
I installed a Leviton smart switch in a 3-way circuit and the corresponding coordinating switch in the picture (right switch). The lights function as they should using both switches.
However, I recently was about to install another switch on left side of the box, when I looked at the...
Hopefully an easy one without much debate but I've just had spoke to someone who has had an electrician go to his rental property and say it needs a new CU which I'd agree, all sockets to be replaced as they don't have switches which I would personally but didn't think this was actually a...
I tested an IEC lead that was crossed L--N . Both ends were sealed, so I cut the cable &
the plug was cross wired. I am posting this because somebody may be churning out
hundreds of cross wired sealed plugs, & how is anybody to know?
Best regards.
Good afternoon!
In my house, I have a three-phase power system and this RCD that's rated for 40 A max and 30 mA leakage current. It keeps constantly tripping on loads larger than a phone charger (ie an electric kettle or toaster). This house is to EU standards (I live in Latvia).
I'm wondering...
Hello, could someone please explain/diagram how to wire two switches (I think DPDT switches are necessary) together so that the electric window in my car can be operated by either switch at any time? (Like when the passenger window of a car works from the driver's switch or from the passenger...
Hi
Firstly if it wasn’t for this forum I would not have been to able to wire my hive controller so quickly so thank you !
Still sort of on topic of my hive I need to disconnect my old wired stat. I believe two of the wires will need connecting together to complete the circuit. Could anyone...
Hello,
I applied for a retrospective completion certificate for kitchen relocation. The work was done about 7 years ago. The building standard surveyor says that I need to install interlinked smoke and heat alarms to comply with the new fire regulations. I got in touch with different...
Hi All,
Apologies, I know this question has been asked a bunch before but as I’ve read in most of the previous threads there is that many different setups and doorbells I wanted to confirm (or not) that I was on the right track.
Plan is to power via current chime. Not sure what make/model but...
Hello
I’ve just purchased a Honeywell Wired T3 thermostat to install. I’ve ran into an issues I have Drayton thermostat in the hall wall which I’m going to replace but I also have Drayton programmer upstairs in main bed room which only controls heating not water the boiler is located downstairs...
Hi,
I have purchased a Ring Video Doorbell in the UK, and am looking to install it. I live in a New build property and the transformer to the Chime is within the Chime unit. Looking at it the wires come through slightly differently to the installation video, and I'm trying to confirm how I...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc