Hi All,
I am looking to install a Quinetic double gang in line receiver switch (QURS2W) in my hallway on the ground floor to control the lights in the hallway on the ground as well as the first floor.
On the first floor, I propose to pair up a 2 gang Quinetic switch.
The wiring is all old and...
Hello, I hope you are well, I have fitted a few Nests but only to Combi, S and Y plan systems just been looking a job where I’m doing the kitchen, looks like the heating system is a C plan?
There’s 4 cables at the programmer, power in two 3 cores up to the wiring centre then a flex to the...
Forgive me if this is easy to search - I was not able to find anything obvious here or on YouTube. I've got an outdoor circuit that has failed. Specifically, one outlet failed and then the second one went about a year later, with no trip of the breaker. How do I test the wiring to make sure it...
Hi. I am trying to replace a heating timer with a smart switch. The current timer is the type with a dial on the front and 1 to 24 written on it where you pull out the little lugs to set what time the heating comes on and how long it runs for, APT is the make. The wires coming from the wall are...
Good evening,
I wondered how the MCB between RCD and the Main switch is wired while watching this video. Photo attached.
I assume a busbar link is connected to the main switch and mcb. Do the line conductors and the busbar connected at the same terminal and then go to the RCDSs?
Link to the...
I live in a flat in Scotland supplied with an old 2 meter system called THTC where one meter using a time signal supplied heating and hot water etc and the other the remaining circuits ie lighting and sockets etc. The flat was professionally rewired about 2 years ago and although there is no...
Hi at a property with a videx vx8000/s keypad entry and art 836 intercom with connected phone with gate button on phone.
After a drilling disaster I had to Replace the videx vx8000 with new unit and it now works with code and gate fob, but intercom gate opening button is inop. Believe when I...
This is a great forum! Am a stairlift, electric scooter, electric wheelchair, repair guy. Also fix broken parts. Also use electricity to multiply tree growth and fruit production. Also use currects for my health e.g. heal myself as Dr. Tennant teaches. Also use electrolysis to make my own...
Hello.
I am new to wiring and could use some help getting this circuit wired in the kitchen . I am trying to get the source power to the GFCI and then through a switch to have the garbage disposal protected by the GFCI. I also have a switch that I would like in for the above sink light. Lastly...
Hello, my house was built in the 1950s and every time I look behind a wall plate the wiring isn’t how it’s shown in any DIY book I’ve read. I’m trying to replace a switch with an LED-friendly one. Wall j-box has two cables coming in, one has 2 wires and the other has a 3rd wire that’s red. The...
Once again I am using the Engineering chat as I think my question is more theoretical rather than 'diy advice'. If I am misusing the forum, please let me know.
This question is back 'in the car' again, but I think it is a fundamental question about 'how electricity works', more so, a circuit...
Hi everyone,
I really hope someone will be able to help. So last night I tried to change 2 ceiling rose / pendant lights at my mother in laws newish build with ones I bought online. The bedroom has 3 lights, the main one in the middle on 1 switch, and 1 in each corner of the main wall (2) on...
Hello everyone.
I bought some property in northern Michigan. It has underground electric with a transformer already on the property. I would like to put in 2 RV panels that are 50A each. The county will let me do all of the work myself with the exception of hooking up the meter to the...
I am wondering how I would wire two 1000w 48v batteries in parallel. They have "t-plugs" to connect them to a controller but I'm not sure how I could connect them to 1 t-plug so they can be connected to a controller. just to clarify this is for an e-bike build, I need to wire them in parallel...
I get wanting to do a good job but does being super neat inside a board really make it a better job?
I don't see any advantage to it aside from aesthetics and if it's something that's not seen then....what's the point in obsessing over how neat it all looks?
To me it's a bit like a kitchen...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc