C2 for extension lead on washing machine | on ElectriciansForums

Discuss C2 for extension lead on washing machine in the Periodic Inspection Reporting & Certification area at ElectriciansForums.net

Dr Denis

DIY
Joined
Mar 31, 2021
Messages
1
Reaction score
3
Location
London
I let out a flat and had an EICR, carried out, to meet the new Private Rented Sector Regulations. The EICR has recorded a “C2” for an extension lead on a washing machine.

The lead supplied with the washing machine is about 1 metre shorter than is convenient for fitting the drainage tube back into the drain, when moving the appliance in and out from under the kitchen worktop. I have fitted a short extension lead between the appliance plug and the 3-pin socket. The extension lead is adequately rated at 13amps and is tucked away such that it is not a trip hazard nor exposed to any risk of mechanical damage. The EICR received, states: “Trailing lead feeds washing machine, Classification Code C2”

I have queried this for two reasons:
1. The trailing lead is not part of the fixed wiring and is therefore outside of the scope of the EICR, which I requested, i.e. to meet the requirements in the Private Renting Regulations.
2. The extension lead is not being used in an unsafe manner and does not merit a “C2”

The Contractor say an extension lead on a washing machine is unsafe and therefore a C2. What comments?
 
A satisfactory eicr is not required to let the property out.
you have an eicr now.
your responsibility now is to repair any c1 or c2 issues within 28 days.

this may be as simple as screwing the extension socket to the wall behind the machine and fixing the wire so it is not trailing.
make a note of the repair that has been done and attach it to the eicr, keep for your own records.

a satisfactory eicr is not required as long as you have documented the faults have been repaired.

edit,
I also think the c2 is probably unwarranted and should at worst just be noted in the comments.
 
Not enough sockets, I believe should be gone. C nothing. But the electrician is concerned as they do burn out and melt more than you think, even tho 13A fuse.
 
If the extension socket was screwed to the wall, and the cable clipped in place, I might consider it part of the fixed wiring, and would class it C3 as a bodge that needs improvement.
If it's not fixed at all, it's nothing to do with me if doing an EICR, although I might mention it in the comments.
 
Sticking my neck out here but I have a couple of houses i do ISITEE on and they both have massive "American Style" Fridge freezers, I installed good quality extension leads on them. This means when i test i just fish the cable up, test the fridge then test the extension, pop them back on top of the units. That means i don't have to manhandle the fridges out to get at the plugs in the sockets behind. These extensions are not used for anything else, don't suffer wear and tear by being unplugged many times.
The OP's washing machine is a similar case.
 
More in the remit of PAT test.
Deffo not part of the EICR, as others have said.
Sounds like I will cover my rear !! and then cover a bit more !!!
I must admit with this Landlord thing I do wonder how many very confident Sparkies will end up being dragged over the coals 5 years from now when some other I'm the dogs danglies U Tube brigade Sparky starts second guessing the 1st guys EICR.
Something like " The last guy didn't know what he was doing look !! this reading is 0.00002 out, terrible" And these code 3s are code 2s. Look at my NAPPIT codebreakers.
But don't worry I'm here now and I'm soooo amazing.
You can find me on U tube and I've been qualified for 2 whole years. ?????
 

Reply to C2 for extension lead on washing machine in the Periodic Inspection Reporting & Certification area at ElectriciansForums.net

News and Offers from Sponsors

  • Article
Join us at electronica 2024 in Munich! Since 1964, electronica has been the premier event for technology enthusiasts and industry professionals...
    • Like
Replies
0
Views
321
  • Sticky
  • Article
Good to know thanks, one can never have enough places to source parts from!
Replies
4
Views
848
  • Article
OFFICIAL SPONSORS These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then...
Replies
0
Views
971

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top