Clamp meter that will measure milli amps

[Haworth]

Afternoon all. I’m looking to invest in a clamp meter but want want that will measure milli amps (nuisance tripping etc). The megger 305 seems the best about; is there any others out there? TIA.

 

[Bob Geldoff1234]

If you don't want to spend that much then i can recommend this one.

HandyMAN TEK775 AC Earth Leakage Clamp Meter | eBay

Jaw opening: 1.2”. AC Current – 200mA range. AC Current – 2A range. AC Current – 200A range. 17th Edition Accessories. PAT Testers. Multifunction Testers. Accuracy:+ (5.0%25 of reading + 8 digits).

www.ebay.co.uk

 

[Haworth]

Is it any good for doing nuisance fault finding etc?

 

[telectrix]

look for the resolution. think it's 0.1mA which is fine for tracing earth leakage.

 

[Haworth]

So is that one any good then?

 

[static zap]

So is that one any good then?

You get what you pay for.
(Drop unknowns on the floor = drift)
( compare with a "Known" situation at home for some stability )
But you could pay for quality - and have it banging about in the van -little used for years !
(With all this DC type RCD/RCBO changes ,I'm still unsure what is around the corner)

 

[Haworth]

So, what’s your thoughts? megger or not?

 

[static zap]

So, what’s your thoughts? megger or not?

I'm a cheap skate .. (but once you look into DC -twiddling with zeros is needed on some)

 

[David Prosser]

FLUKE 771 | Fluke 771 Clamp Meter, 100mA dc | RS

uk.rs-online.com

I use one of these. Being able to move the clip separately is handy. Just make sure it pointed in the right direction. I often couple it up with the other one for signal faults, Fluke-709 | Fluke 709 Multi Function Calibrator | RS Components - https://uk.rs-online.com/web/p/multi-function-calibrators/7769529/ . Very handy if you carry out fault finding on your own.

 

[ElectroChem]

@Haworth
Just in case you didn't realise, David is having a bit of fun with that recommendation. Don't clamp a 771 around an AC line, it... won't appreciate it.

As for AC leakage clamps, I use an AEMC model 565. It has a high range to 100A AC, low range to tens of microamps.

 

[telectrix]

View attachment 51091View attachment 51092

FLUKE 771 | Fluke 771 Clamp Meter, 100mA dc | RS

uk.rs-online.com

I use one of these. Being able to move the clip separately is handy. Just make sure it pointed in the right direction. I often couple it up with the other one for signal faults, Fluke-709 | Fluke 709 Multi Function Calibrator | RS Components - https://uk.rs-online.com/web/p/multi-function-calibrators/7769529/ . Very handy if you carry out fault findingView attachment 51091View attachment 51092 on your own.

just seen the price.could buy a van and a MFT for less.

 

[Marvo]

I use one of these; P01120576Z | Chauvin Arnoux MA400D-250 Clamp Meter, Max Current 399.9A ac CAT IV 600 V | RS Components - https://za.rs-online.com/web/p/clamp-meters/7781059/

It's small, CAT IV rated, convenient with a flexible clamp and pretty accurate down in the low miliAmp range as well as up to 400A. Had it a few years and can't find fault with it (pun intended).

 

[oracle]

My current clamps are :
fluke clamp 1:1000 ratio producing 150A from150mA DMM output
Fluke 360 reading from 1uA to 60A brilliant for tracing fault currents.

 

[Pete999]

Is it any good for doing nuisance fault finding etc?

What sort of "nuisance fault finding"?

 

[oracle]

What sort of "nuisance fault finding"?

Pete,I’m guessing Harmonic hum, or over sensitive RCD tripping