Dodgy trade pictures for your amusement! - 1 Million Views!

[Darkwood]

Right ... Just been nudged to set this up by Paul.M and sounds a good idea following recent threads I've done in the Arms..

Rules....No Offensive material... edit if required before posting as this is the public arena.
Anything to do with the trade or in and around it ...H&S pic's welcome.



I've posted this a few times and this is at a mates house following a kitchen refirb several yrs ago. mg_smile:

 

[freddo]

It goes to the front cover that is resting on top.

 

[NDG Elecs]

Hi again

don't want to hog this thread but... first job of day after last post.

This actually had an eicr for a Cu change issued by the installer saying all was satisfactory with nice pic of his ecs card....

C3 ! for no MPBC to water and gas was all that was picked up!!


Any comments

View attachment 33624

View attachment 33625

View attachment 33626

View attachment 33627

Never seen PME like that before...is that defo legit? I would be on the phone to DNO to check their records as to whether it is their PME or some dodgy conversion..

 

[NDG Elecs]

It goes to the front cover that is resting on top.

That's diligent mate, especially for domestics. But fair play...

 

[freddo]

That's how they are supplied from the manufacturer.

 

[NDG Elecs]

That's how they are supplied from the manufacturer.

Ah OK..... So you are slack like the rest of us then!!! Haha!!

I have never fitted any lewden gear before.

 

[eggandspoon]

Hi again

don't want to hog this thread but... first job of day after last post.

This actually had an eicr for a Cu change issued by the installer saying all was satisfactory with nice pic of his ecs card....

C3 ! for no MPBC to water and gas was all that was picked up!!


Any comments

View attachment 33624

View attachment 33625

View attachment 33626

View attachment 33627

HI

This is not marked as a PME supply (TNCS) I have the DNO coming out for a look - to ensure a proper pme conversion if required or a main earth put in from their box. There will be a Henley box somewhere as it was a common stair, but I didn't have time for a look.

IMHO the installer should have ensured there is a proper main earth terminal - regardless of how it was done before.

Every PME install I have ever connected to has been marked and a consumer earth terminal provided - but if this was ever an approved method of main earth corect me if I'm wrong.

 

[Dave OCD]

That's how they are supplied from the manufacturer.

That's a lovely job Freddo, I'm glad there are others as fussy as me out there.

 

[freddo]

British Gas woz ere.

WTF?!
Unfortunately I both touched and broke the seals in order to remove a lighting fuse. What's worse is the fuse carrier had a bit of 1.0mm2 in it, nicely sealed in.

 

[freddo]

Was called out to a pub where they were unable to reset a socket circuit RCBO. I spent some time finding all the appliances connected to the circuit and disconnecting them so I could insulation test the circuit, then break it down until I found the fault which was a cable between 2 sockets. A look of the likely route showed a cable clip holding the flex of an extension lead to the wall (ew) in the sockets safe zone. A bit of a dig with a chisel confirmed where the fault was. The blast had severed the CPC.

What was really annoying was it was obvious someone there had nailed the cable, (the box of clips and a hammer was on the table in the photo) but they didn't want to admit it as they would get the bill for the call out and repair, so instead they all stood and watched as I moved furniture and equipment to access sockets when they knew damn well where the fault was. When I called them out they said the extension cable had always been clipped there. In the time it took to find the fault I could have replaced the cable.

 

[NDG Elecs]

British Gas woz ere.
View attachment 33672
WTF?!
Unfortunately I both touched and broke the seals in order to remove a lighting fuse. What's worse is the fuse carrier had a bit of 1.0mm2 in it, nicely sealed in.

Nice easy way too maintain IP rating there Freddo! I like the way thin strips have been especially cut for the RCD tails.

 

[freddo]

I don't know what they were trying to achieve!

 

[leo79]

I don't know what they were trying to achieve!

They get pulled up for holes left on electrical equipment, classed as a 'near miss' in some instances so everything gets taped or filled with silicone. Looks crap but only keeping there job.

 

[freddo]

Since when is a customers electrical installation the responsibility of a meter fitter? If they are happy to connect perished fabric/rubber tails to a meter a Wylex fuseboard should not be of concern.

 

[leo79]

I didn't realise it was the meter fitter who taped all the holes up. I'd be surprised if a meter fitter would even touch the consumers installation.
I was referring to BG electrical division who are told to cover/fill any holes they come across.

 

[Had8Lives]

Just gonna leave this here..

View attachment 33392

Who ever did that has never heard of an IP box then?