Dodgy trade pictures for your amusement! - 1 Million Views!

[Darkwood]

Right ... Just been nudged to set this up by Paul.M and sounds a good idea following recent threads I've done in the Arms..

Rules....No Offensive material... edit if required before posting as this is the public arena.
Anything to do with the trade or in and around it ...H&S pic's welcome.



I've posted this a few times and this is at a mates house following a kitchen refirb several yrs ago. mg_smile:

 

[James]

For a finished job, it’s unspeakably bad.
but as said before, if the ceiling is about to be dropped then it’s not a bad job.

 

[swaRRR]

Just been sent these from a friend. Plasterer had been asked to go and make good the ceiling.

Seems the ‘electrician’ told the old dear that it was the only way to do it because it was a flat roof. Basically taking advantage of her.

She’s now left with a hefty bill for a suspended ceiling to be done or get another electrician to rectify.

View attachment 98426View attachment 98427View attachment 98428View attachment 98429View attachment 98430

I'm literally flabbergasted at this work. I'm lost for words.

 

[swaRRR]

If the gate opens into the garden, then it works doesn’t it?

It works but it's inside out and back to front lol

 

[Fazz711]

Friends had to do the same after dog learned to flick latch and open the gate

Not electrical but my dad's next door neighbour..

 

[LewisM]

What i've done in the past with flat roofs is cut two channels out and fish cable across then that way you can put the old cut strip back in and do minimal making good.

 

[freddo]

Just been sent these from a friend.

I couldn't ever even imagine attempting to carry out work like that. If the flat roof was that much of an issue it would be better to just pull the ceiling down, wire it and then fit new boards. Who would want to try and batten over all that lot now anyway?! Wrecked the nice coving too.

I've just looked at those photos again, that wiring is so offensive!!!1!1!!

 

[marcuswareham]

Apparently the electrician told the old dear that she would have to have a suspended ceiling as there was ‘nowhere to run the cables’ with it being a flat roof ext.

Which as we all know is bo**cks as there is still a ceiling void.

The down lights are flush so they must be in some kind of void

 

[swaRRR]

What i've done in the past with flat roofs is cut two channels out and fish cable across then that way you can put the old cut strip back in and do minimal making good.

How do you get through joists with this method? Is the strip big enough to get a drill in?

 

[Baddegg]

 

[Dartlec]

View attachment 98438

Just as well you got a picture of my van on a good day.... (and yes it's blue)

 

[Dartlec]

Stevie Wonder electrical is back in business! At least he got the CPC right.

View attachment 98421

Did you check that he didn't rewire the plugs to compensate.....

 

[Mike Johnson]

Just as well you got a picture of my van on a good day.... (and yes it's blue)

I thought that was how they come from the dealership?

 

[Simon47]

How do you get through joists with this method? Is the strip big enough to get a drill in?

Alternative, though not very nice, method is you cut a chase in the plasterboard across each joist. You then fish across between the joists, drop under one using the slot, then fish across the next gap, and so on. Then you're left with a row of smallish holes to fill in.

 

[Baddegg]

In that situation I’d go with @LewisM, bite the bullet and cut 2-3 big wide strips out with the multi and then just put em back up and charge for a ceiling skim to make good

 

[LewisM]

How do you get through joists with this method? Is the strip big enough to get a drill in?

Yeah if you do it wide enough, normally I just do a small notch and use a safe plate, once filled and painted you can't tell.