EICR prices - 3 bed semi or per certificate? | Page 3 | on ElectriciansForums

Discuss EICR prices - 3 bed semi or per certificate? in the Periodic Inspection Reporting & Certification area at ElectriciansForums.net

Literally anyone can carry out an EICR...and I mean anyone. I bet a lot of wet pants consider themselves competent.
They are not even notifiable works.
There is practically no record of anyone ever being injured by a poor EICR or a person testing being prosecuted for poor certification.

So, why on earth is anyone surprised at the absolutely diabolical part of our industry, that is EICR, is over run by chancers and cowboys ??
 
Literally anyone can carry out an EICR...and I mean anyone. I bet a lot of wet pants consider themselves competent.
You are correct. I've lost EICRs to wetpants in the past.
There is practically no record of anyone ever being injured by a poor EICR or a person testing being prosecuted for poor certification.
It's only a matter of time before a fatality occurs, I reckon. When rather than if.
So, why on earth is anyone surprised at the absolutely diabolical part of our industry, that is EICR, is over run by chancers and cowboys ??
I for one am no longer surprised by the appalling standards that I see in the greater Glasgow area week in, week out.
[automerge]1567116540[/automerge]
Prices for EICRs up here in Glasgow are ridiculously low. Ditto rewires and just about every other type of domestic work. Although the prices I charge are above the typical prices for this part of the country, they're still relatively low when compared with the prices some of you lucky guys down south are getting.

JK Electrical - Terms and Conditions - http://www.jkelectricalservices.com/pages/terms_and_conditions.html#eicr
 
Last edited:
ÂŁ175 is my absolute minimum for any property. It's hardly ever that cheap though.
There are loads round here who make them up and go in and out in 40 minutes or so for ÂŁ60. They are very popular with landlords.
I charge ÂŁ150 for a standard 1-2 bed flat and ÂŁ250 for a standard 3-4 bed house, any bigger and it's estimated on time or per circuit! I seem to do a lot of houses but not so many flats, mainly student let houses too.
Same here I charge around ÂŁ220.00 as a Min. standard on a 2 bed House or Flat with a 6/8 way D.B takes around half a day 3 to 4 hours, then on my P.C. to issue a report etc, funny how some Electricians can do it for silly money as I will check at least drop off a socket & switch in each room, check outside the property for external electrics etc. also earthing for Gas water & Oil bonding or if cross bonding is required also, if cables or visible are supported correctly the correct selection of breakers/fused for circuits they are serving.
its not a quick thing as we are there as experts in our field and should give a good account of it.
so when I hear its too dear, I walk away as you will also get a taker and wish them good luck lol
 
Same here I charge around ÂŁ220.00 as a Min. standard on a 2 bed House or Flat with a 6/8 way D.B takes around half a day 3 to 4 hours, then on my P.C. to issue a report etc, funny how some Electricians can do it for silly money as I will check at least drop off a socket & switch in each room, check outside the property for external electrics etc. also earthing for Gas water & Oil bonding or if cross bonding is required also, if cables or visible are supported correctly the correct selection of breakers/fused for circuits they are serving.
its not a quick thing as we are there as experts in our field and should give a good account of it.
so when I hear its too dear, I walk away as you will also get a taker and wish them good luck lol
Price Varys with myself if its in occupied property and not a nice one to test due to cleanliness I add more money which the landlord understands but bottom end I charge ÂŁ120 on 1 Bed Flat/ Bungalow (Clean) then ranging up to ÂŁ250 for 3 Bed House (Dirty)
 
I charge on average ÂŁ175. I wouldn't negotiate, unless less work is required. I can't remember anyone ever saying 'no'.
It does sound as though prices are a bit area dependant though.
 
Literally anyone can carry out an EICR...and I mean anyone. I bet a lot of wet pants consider themselves competent.
They are not even notifiable works.
There is practically no record of anyone ever being injured by a poor EICR or a person testing being prosecuted for poor certification.

So, why on earth is anyone surprised at the absolutely diabolical part of our industry, that is EICR, is over run by chancers and cowboys ??
Welcome to Britain! Anyone can install electrical equipment and wiring providing it's done in accordance with BS7671 regulations. If it's Notifiable the Building Authority must be informed but someone else will probably do it.

Anyone can inspect and test installations provided they use test equipment to BS EN 61010 and BS EN 61557, recording the results on any piece of paper provided that it contains the required information in appendix 6, BS7671, although other test methods can be used provided they give valid results.
All these things depend on compliance with BS7671, only it's not statutory so you don't have to. ?
 
I suspect the cheap EICR will carry on until someone does jail time for missing an obvious fault and someone gets killed.
The problem with this is that EICR's rarely involve 100% sampling and are required to be carried out with minimum dismantling (GN3). This means that any points not part of the sample could be hiding a dangerous fault even on a properly carried out EICR, I think that is something many good electricians do not appreciate. If we advocate draconian measures for those who miss something on an EICR then it will have to be 100% sampling on all installations or none of us will be safe, not just the drive by brigade.
 

Reply to EICR prices - 3 bed semi or per certificate? in the Periodic Inspection Reporting & Certification area at ElectriciansForums.net

News and Offers from Sponsors

  • Article
Join us at electronica 2024 in Munich! Since 1964, electronica has been the premier event for technology enthusiasts and industry professionals...
    • Like
Replies
0
Views
381
  • Sticky
  • Article
Good to know thanks, one can never have enough places to source parts from!
Replies
4
Views
959
  • Article
OFFICIAL SPONSORS These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then...
Replies
0
Views
1K

Similar threads

Echo above, as someone who's probably similarly inexperienced I have set myself up a per point spreadsheet and whack it all in there. This has...
Replies
9
Views
584
Thanks mate for the advice, this is just what I was looking for. I think I’ll have to put some thought into the domestic route due to the NVQ and...
Replies
2
Views
368

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top