what is the worst cable you have stripped?

[shanky887614]

stripped some about 5 X 5pair version of this



swa is fine, the stuff we stripped though was like the one about but it took longer to get rid of the screen because it was tapped as well than the strip and terminate the gland


can't find a picture of the cable as they were existing so i don't know exactly what they were (control wiring)


it had a blue sheath though

 

[Sintra]

Remember doing a couple of bootlace SWA's into isolators in Prague during the winter. Was -23 and a total pain fingers were numb after a minute.

 

[Des 56]

Remember doing a couple of bootlace SWA's into isolators in Prague during the winter. Was -23 and a total pain fingers were numb after a minute.

I bet the nights out as a single in Prague made the pain that much easier to bear

 

[Sintra]

Well I must admit working in Praha for 8 months was fun lol

 

[Robotstar5]

Probably the "fiddlyist" (is that a word) I have done was 3 cables each with 7 x 7 cores (total of 147 cores) made off into high density Harting plugs. I hated having to fit the spare to a machine as I knew it would take me the next 2-3 shifts to make a new one!.

 

[gnuuser]

pulling an IS machine controller cable and pinning it in the connector
1 inch thick cable of 50 conductors
a beast to pull through raceway as it very heavy

 

[Knobhead]

Never had a problem with large SWA’s in cold weather. Helps having always worked on kilns and furnaces, just roll the drum under the kiln for a day or so.
My big bugbear was as others have said, no French chalk and the serving stuck to the insulation/armourings/cores/its self on the drum. Had it on all kinds of cable and can’t point to one particular manufacturer, all seemed to have off days.

Had one that really confused me. My mate and I had made the supply off to a MCC everything OK, went to the switchgear stripped the outer serving and armours off, at that point we both got very confused. Went back to the panel the inner serving was extruded, back to the switchgear it was taped ? ? ? ?
We had run a few cables the same size, must have got them mixed up somehow. Did a few quick tests, we’d got the right cable. All the cables had come off the same drum, some were taped some extruded.
I do remember who supplied this cable, BICC. Phoned them up with the batch number, “Oh that’s where it went. You shouldn’t have got that.”
It seems they can swap servings without stopping the line, we copped out for the bit in the middle. It tested OK so it stayed in.
That’s going back some time, it was just before I came out of my time.

 

[Deleted member 9648]

Not the worst by any means but ancient Hi-tuf is in the top ten. Outer sheath made of granite and cores and inner sheath welded together....fun on a cold day.

 

[Kate]

Lsf. I have given myself black eyes, cuts to eyebrow forehead many times!! You bleed more when its cold.

Have had a few t+e with no powder in so sheath stuck solid. All swa's have been good

 

[shanky887614]

Lsf. I have given myself black eyes, cuts to eyebrow forehead many times!! You bleed more when its cold.

Have had a few t+e with no powder in so sheath stuck solid. All swa's have been good

T+e knife down middle?

 

[Thefailsafe2012]

Worst I can remember was a 19 core 1.5mm pyro that had to be stripped 1200mm to get into a BMS panel.

That sounded fun :sad:

 

[baldsparkies]

What is the worst Cable you have ever stripped !!!

Tony Cable from the NICEIC !!
Not a pretty sight naked lol.

 

[Engineer54]

Double steel tape armoured cable, that stuff top's anything that's been mentioned here so far!! lol!!
I'm surprised that Tony didn't bring it up in his post above?

That steel tape can be like sprung steel, i defy anyone stripping/terminating that cable not to cut their hands to ribbons. Single steel tape cables were/are bad enough, but the double steel tape cables are an absolute nightmare. Thankfully you don't see them much any more, but are still produced for locations where additional mechanical protection warrants their use. That would mainly be in heavy industry situations...

 

[benji]

stripped one end of a .3 dwa pilc at cotgrove colliery in the sixty,s kept burning my fingers cleaning armours it kept the jointer amused

 

[CockneyReject]

35mm 4 core LSF armoured I did the other week tops my list, been sat outside for a week so was solid then the outer sheath stuck to the armour, inner sheath took some getting off too then there was the plastic crap aswell, had to strip 3m then fight getting it over the containment and into the trunking

oh and then after that there was 30 rings all in LSF twin to put away into the power side of the board

 

[Sintra]

That sounded fun :sad:

Absolute nightmare. By the time the cores where all lined up to get the seal on the moisture was already getting into the mineral.