Search results

Search results

You will need 50 posts under your account before joining in with this thread because you can't link out without 50 posts first.

  1. Lee42

    ksr calanda installation

    Hi all. I have a job of wiring 3 lights on a tarmac drive with a block border. The customer is set on the ksr calanda bollard. Problem with it is there is no way you are getting 2 swa into them fittings. Either side of the drive is neighbors driveways so not possible to have swa on a post...
  2. Lee42

    Brushed Steel Screwless plate - which Brand?

    Fitted plenty of the bg nexus flat plate over the years which had the sector branding. Not been back to one yet (touch wood) Mk is always been my usual choice, but for the price u can't go wrong
  3. Lee42

    Replacing Heating Controller With Nest Heat Link

    Remember the nest thermostat needs wiring back to heat link as it is 12v Unless u are not putting it in old thermostat position, and are plugging it in somewhere
  4. Lee42

    Replacing smoke alarms

    I woul I would recommend going for the lithium version. Can fit and not worry about batteries running out
  5. Lee42

    Replacing smoke alarms

    Go for the ones which have the 10 year lithium batteries,(ei161). you will be replacing the 9v batteries when they run out in the other units, and cursing at them when they are bleeping in the middle of the night
  6. Lee42

    Running a radial circuit in bedroom. He

    If the CU was replaced in 2016. Your installation should of already been tested.
  7. Lee42

    Bungalow under floor heating

    Most I have wired have required a extra core for the night set back mode. I have also wired one where the stats needed a cat 5 to them. Most work better with a floor sensor in too. Best thing to do is read the instructions throughly
  8. Lee42

    Problem with a timer fan on light circuit

    No led lamps on the circuit?
  9. Lee42

    EICR's and previous editions of Regs

    I have done 7 eicr this month. Some passed, some failed. You can only test the installation to the current regs. If it's an installation from the 16th edition it doesn't mean it's going to fail. The most common c2 I write down is no supplementry bonding in bathrooms without rcd protection. No...
  10. Lee42

    Kitchen Led under cabinet lighting

    I agree A type c breaker should solve the problem. We tend to fit type c on lighting breakers. Helped stoped breaker tripping when a filament lamp came to the end of its life too
  11. Lee42

    Electrical water heater problem

    He said it was tripping out. But still hasn't come back to us about what part is tripping out. Most of the time on a water heater it is to do with the safety cutout. Unless the element is starting to fail.
  12. Lee42

    Electrical water heater problem

    It will more than likely be the thermostats safety cut out that is tripping. Get them happening alot in immersion heaters. Try lowering the temp down on thermostat. If it still trips, you will probably need a new thermostat. That's if the safety cut out is built into the thermostat. Couldn't...
  13. Lee42

    Price check please, NI sparks in particular.

    I agree Sounds a fair price. Did you just give a verbal price?
  14. Lee42

    Electric Underfloor Htg

    Yes sure Will have to have a look in the office tomorrow. I always try to take a picture of the mat down, and the ohm reading on my multimeter. Just incase anyone tries to pin the blame on you.
  15. Lee42

    Electric Underfloor Htg

    We have used a firm that come out to remair mats They were brilliant. Used a thermal camera to pinpoint damage. Repaired the Matt with minimal damage to floor. Did u take a reading of the resistance of the Matt before and after laying? Matt normally has a figure in ohms attached to it
  16. Lee42

    Wifi light switch issue

    I would also advise to put a deeper faster fix box in, as it will be very tight with the one u have in now
  17. Lee42

    Wifi light switch issue

    You will have to make some adjustments in the other 2 way switch, to make that light work, as the switch wire is in the other switch
  18. Lee42

    Wifi light switch issue

    That wont work as a two way switch.
  19. Lee42

    CPN cudis lumo consumer unit

    We have been fitting the schneider boards as they are on offer. Only gripe I have with them is the neutral bar is running down the sides, when changing a board, neutrals are normally short. Couldn't beat the old square d quickline board
  20. Lee42

    Unvented system wiring help

    I thought that was only when connected via a boiler? You mentioned it is only heated via a immersion which will have its own safety cutout

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top