Search results

Search results

  1. R

    Speaker Cable for DoorBell

    Thanks littlespark Its just a standard Byron bell push Ive attached the link from screwfix website below...
  2. R

    Speaker Cable for DoorBell

    Good evening Guys Was wondering if someone can advise. Ive wired a door bell system on a job in speaker cable( was last minute floors were going down and only thing in the van) However when connecting up the kit as per instructions i cannot seem to get it to operate. Is speaker cable...
  3. R

    External Consumer Unit

    Good morning guys Was looking for advice with regards to installing an outdoor consumer unit. Customer is looking for power to be installed from there property to an area in there garden. There installing a future hot tub and summer house and any future lighting and power. They currently have a...
  4. R

    Rangemaster Cooker Load

    Done a quick calculation as per Page 122 of OSG and it should pull in 27 Amps with Diversity applied.
  5. R

    Rangemaster Cooker Load

    I've just checked the manufacturers installation booklet again I've just checked the manufacturers Instruction and it states a 45Amp Fuse Rating. Nothing about size of conductor but a 10mm should be suffice on a 50amp RCBO. Cheers for the pointerđź‘Ť
  6. R

    Rangemaster Cooker Load

    Hello Guys Looking for some advice with regards to a extension job. Customer has ordered a Rangemaster Induction Hob and Oven. I've looked at the specification and it states that potential full load is 14.8Kw. My initial plan was to run a 10mm Twin and Earth but I'm wondering if it would...
  7. R

    2x 9Kw Electric Boilers

    Good morning Guys Looking for some advice with regard to a current job. Building company I'm doing work for are installing Electric heating on a property. Customer has no access to Gas so there are 2x 9kW Electric boilers being installed. (Plumbers and Builders...
  8. R

    EV Charging- Becoming OLEV approved

    Evening I have recently sat my City and Guilds EV charger course and am now looking to become OLEV approved. I was wondering if anyone had any advice on what the process of doing this is Thanks
  9. R

    S Plan Heating with UFH

    As far as im aware the UFH system is heatmiser. The roomstats are Neo stat V2. Thats pretty much all I know at the minute. I know the UFH manifold is external to the main wiring centre so I was going to run A 3 core and earth between the wiring centre and the heatmiser wiring centre. A...
  10. R

    S Plan Heating with UFH

    Thanks for the quick response brian. The UFH system has separate stats for each individual room downstairs. I will make sure I use a stat for the upstairs radiators. Thanks again
  11. R

    S Plan Heating with UFH

    Hi guys Looking for some advice with regard to wiring a heating system. Starting a new build next week and have little if any experience with heating systems. The heating system is a system boiler with a cylinder. There is radiators upstairs and an UFH downstairs. I understand the wiring setup...
  12. R

    Labour only pricing on new build

    Thanks dave. Thats roughly what alI was thinking as well. I will be working alone on the project. Cheers for the response
  13. R

    Labour only pricing on new build

    Evening Looking for some guidance on pricing for new builds. Ive been asked to put in a tender for labour only on 4x new build timber frame properties. 4x bedroom with Living/ dining room 2x bathrooms and an ensuite. Spotlights in every room ( 50 ). System boiler with unvented cylinder...
  14. R

    New build development pricing

    Hi there. Looking for some advice on pricing for a new build development. Clients is supplying material so its a labour only job. Not quite sure about how to price for it. Its a 2 storey 4 bedroom plot. Pendant fittings in very room except spotlights in kitchen/dining room. UFH in downstairs...
  15. R

    Meter tails over 3 metres???

    ?? yeah i think i pressed enginerr by mistake haha 1580056871 I think i need to reset my profile details ?
  16. R

    Meter tails over 3 metres???

    Im not an engineer im an electrician with a mainly commercial background.
  17. R

    Meter tails over 3 metres???

    No the above isnt me. Like i say No the above isnt me I have recently started self employed and it was something i have not come across before so wanted clarification on it.
  18. R

    Meter tails over 3 metres???

    Its not something ive had to do before richy3333. The whole point of this forum is to help and discuss. I thought the correct way to do it was the way which has been stated above but i doubted myself when i was told to use an isolator. Hence why i came on here to get some reassurance. As this is...
  19. R

    Meter tails over 3 metres???

    Another sparky advised me ob this?
  20. R

    Meter tails over 3 metres???

    Thanks SJD. I thought id have to protect it with my own fuse inwas just want to doible check. Thanks for the rrsponse.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top