while doing EICRs i often find this combination, if its clipped direct it dont worry me
however many times i have no idea how the cable is routed
im just wondering how others would code this?
I am not an Electrican but I am buying a new home here in Michigan, and the outside pole to the house I’m wondering if is a 100 or 200 amp service coming from outside, I talked to to electricians in person without them coming out to the house just from the pictures to see if they know the...
I am getting an electrician in to fit a new consumer unit to provide an extra 32 amp cable/supply for a new cooker.
I cant see how the electrician would be able to get a new cable from the garage where the consumer unit is located to the kitchen.
Is it common for electricians to not be able to...
Evening all, apologies if this is in the wrong forum or has been asked before.
I have ordered a new oven thinking I could just plug it in to 13amp socket same as my old one. However I checked today and the oven is 16amp and therefore should have its own dedicated circuit.
I checked the...
I have a range cooker with 1 oven that is electric and runs on a 13amp plug instead of the usual hard wired cooker connection. The original instructions (now mislaid) said that it should be plugged into a 13amp outlet, not an extension. I cannot move the cooker to see the plate to verify the...
Hello
Is it OK to use a 32 amp rcbo on a radial Circuit. Cable size is 6mm2, cable length is about 15 m. There are 4 double plugs on the circuit. Loads are kettle 2.2 kw, washing machine max 2 kw, electric cooker 1 kw.
Cheers
The double 13 amp socket which we use to power the TV and recorder has tripped the RCD. The only change to the wiring was the installation of the new consumer unit about four years ago.
The house was re-wired about 12 years ago.
We are now using a double socket with an extension lead for the...
Hi
Quick question,
I have the following appliance lying around and wanted to make use of it, it comes with a German plug with the following specs;
1000 Watt
220/230v
50/60hz
What earthed/grounded schuko adapter will I need, a 5 amp or 13 amp? I know the UK version of the same model uses...
Carrying out and EICR on large factory and they have welding plug into 63 amp commando sockets but are protected by 30 amp BS 88 fuses.
Now the regs states Socket outlets with a ratted current not exceeding 32 amp need RCD protection. 411.3.3 (i)
Because the Socket it 63 amp I say it does...
Hi all,
Quick question hope someone can shed some light on.
I have a single coil burner with the following labelled specifications;
1000 Watt
220/230v
50/60hz
It comes fitted with a 13 amp fuse, but after reading a short bit about fuses I got the impression it might be too high.
The...
Hoping to get some advice as i like to understand what work will be carried out and what actually needs doing etc.
Looking at replacing the hob & oven as they are on their way out and in my research I've found out the following.
Oven & hob are both connected to an isolating switch just above...
set up for immersion goes like this for me....
Option 1) 16amp breaker > 2.5mm t&e to 20amp DP isolator > flex from this to immersion.
But how is this set up.....
Option 2). 16amp breaker > 2.5mm t&e to 13amp fcu > flex from this to immersion
Are both fine?
Hi
Is it safe to use a 10 Amp Extension Lead with a 7 Amp Car Battery Charger? Apologies if sounds crass - just need reassurance it's safe please. Thank you.
I am planning to run a power to the garage from a 16 amps RDC from house CU in a new build. I want a power a twin socket, an internal light, and a floodlight. There is a power feed to a junction box on the outside of the house from a CU. My plan is to install a power supply as per the attached...
Hi All, I am installing a new double oven and ceramic hob where a stand alone oven used to be, the oven is rated at 29amp but not sure what the ceramic hob is, current wiring is 10mm from a b40 fuse in the consumer unit to a 45amp cooker switch and plate, I know that I need to change the plate...
Hi
I'm buying a new kiln and wonder which is best on a 60 amp supply in an old house. I have a choice of 7 kw or 9 kw. Will the 9 kw Trip if I run the shower at the same time? Have been advised to install a 50w breaker for the 9 kw.
Just a quick questiin can i use a 3 amp for a 2A fused connection unit the factory manuel is saying 2 amp full stop is this 100% or can i use a 3 amp i would of thought this would be sufficiant and then wired to a 6 amp breaker? Never done a alarm system before so making sure as dont want to pop...
Hi all,
I currently have a cooker control panel with a 13 amp socket but the cooker switch needs to be on for me to use the 13 amp socket.
I remember using at my last place the two where separated and I could then use the socket without the cooker on.
If thats right then what panel do I need...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc