Hi all, I was with my senior yesterday doing a EICR for a domestic house. All of works are fine apart from this shower as shown below.
Shower is low and tiled around. I was suggesting to give it a C2 as water might get in contact for such low height. But my senior was saying it's just a C3...
As of this morning it has been announced that the current wiring inspection system is utterly flawed and we are to adopt our cousins Nec Code. Working to a strict code should improve standards whilst saving hard working electricians from paying hefty subs each year.
Happy April 1st
Gaggenau induction hob fault - code Ci9 ADB R
Today, 08:29 PM
Dear All,
Does anyone have any experience of the induction hob range made by the company Gaggenau? I have a customer who has the above fault being displayed and now the hob after struggling on and off for a few months has finally...
What code would you give when doing EICR for a property that has no supplementary bonding in a bathroom, there is no RCD on any circuit but zs and insulation tests are good,
Is it acceptable to measure the resistance between the shower and pipework, if it's under 0.05 ohm's take it as bonded...
I have been told this is the bible for inspection and testing , would this be the opinion of guys in the field , it defo seems clear and easy to use and it does allow for standardised coding by all ( if everyone sings from the same page )
Any opinions on this book ?
Has any 1 found any...
Hi Guys,
New to the forum, so first post. I need to purchase one of these Mainslink 500 m wireless jobies as communications cable between boiler and central heating has been cut and instead of re-running the cable, this seems to do the job.
Has anyone used one of these Mainslink wireless...
Hi guys
Long time since I've posted and never in the alarm section, so appologies if this has been covered to death.
Basically I have just moved into my sister's flat and I want to start using the alarm. She said she doesn't know the code as she has never really used it etc.
After a leak in...
I'm getting in a bit of a muddle as to whether this is a code C3 or no code.
This is an EICR. The CU has a 100mA main switch. The lights have 100mA protection the rest of the install has 30mA protection. It is a TT.
The Best practice guide clearly says no RCD protection in this scenario is a...
A block of flats has various external lights not just attached to the building but around the grounds. Part of the circuit has twin and earth going underground with good readings but clearly unsuitable cable for external/underground use (not contained in any form of conduit).
The swa on the...
No schedule in distribution boards what code would you give this previous reports state code 3 I was thinking code 2 but a bit unsure factory environmental
Hi Guys,
Just a quick message from @FILPLASTIC :-
For the first time ever, Filplastic are offering 10% off our entire site on orders above £100 (Ex VAT and Delivery) until Sunday 30th September.
FilPlastic already kindly give us 10% off of Tilt Bins on their website, but this discount code...
Dear All,
I wanted to reach out to the community and ask for some assistance. I have a Pyronix Euro 46 and I can't remember the master/user codes although I have the engineer code. Is there a way I can reset the master/user codes with the engineer code?
Thank you for your feedback.
T
After your thoughts on EICR coding for an existing plastic consumer unit in an under stairs cupboard, firstly in a standard domestic dwelling and secondly in a house of multiple occupancy.
After discussing this others and with tech helplines seems to be a bit of a split as to what code!
hi all,
Ok let’s get straight to the question.
Is the below a code 2 defect on a EICR??
A 16amp bs61009 supplying a single 1.5mm FP200 cable with a run of approximately 8 meters, which is feeding a IP rated single socket for a grease trap unit. The socket is low level behind the grease trap...
As above really. My tester is showing an Error 1 code right from switching it on. New batteries, battery terminals all clean, voltage is good at the two terminals on the battery box/holder. All internal fuses are good too.
Is this the end?
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc