Your input please, normally I just make a list of faults and a bright young office thing types up the report and allocates the codes (I think i'm deemed too old and the bright young thing has a degree and the latest version of the test and inspect and a winning way with people and a higher...
I have recently installed a frieland response wireless alarm, iv got it up and working but not exactly how the customer would like, it's the first one iv done, basically iv set the house code on all the accessories as in pir sensors, door magnets n siren, but iv set different zone codes because...
Cj24
Thread
alarm
codes
different
friedland
garage
house
wireless
Hi All
Carried out an inspection on Friday and just fill out the forms and i need some help.
1st- what code do i have to give non shower rated downlights in a bathroom? i think it should be= C1
2nd-what code for for no end to end insulation resistance on the house ring? =C2
3rd-what code for...
Hi Guys
I have a Domestic Installation
One 14way CU with RCD Main Switch in meter cupboard
One 4way CU with RCD Main Switch in garage fed from above CU
One 8way CU in another part of the house fed from a Switch Fuse and RCD in the meter cupboard.
Wiring faults found. Codes required please...
Hey guys , i got my 2391 inspection and testing exam coming up and Ip codes are coming up alot in the past papers, is there an easy way of remembering them ? cheers.
Just been to an inspection today, as with many of them its suffering from a bit of DIY, bathroom downlights are above 225, so are out of zones, but are not IP rated, so I will probably give them a C3 ? They are double insulated but the earths have been nicely snipped out so are discontinuous &...
andyyoyo
Thread
again
codes
double
eicr
fittings
maybe
protection
rated
zones
Been doing an EICR today and would value some opinions please:
The socket is well under 3m from the sink (yes I realise its not a bath or shower) so is this a code at all? Its actually a spur from a double which is in the cupboard so I could simply remove it.
The right edge of the socket...
I few scenarios for which I'd be interested in views what codes to apply......
1) Main bonding is jointed with a choc block in an inaccessible place.
I was going to go with a C3 but not so sure....
2) Main bonding is not continuous from the water to gas. (i.e. one cable to water, separate...
Greetings.
Just done a PIR using the new EICR form, and had a few questions regarding the inspection.
The main bonding is in 4mm and the main earth is in 10mm. Is this a code C2 or C3? There was a thread for recommendations for PIR's on here which is pretty good, so I am going to stick to...
Mattrod
Thread
bonding
codes
earthing
eicr
installation
new
system
Hi,
i did a pir on an old cottage on tuesday. the lady is going to rent it out, so it the installation needs to be bang on. i did all my inspection and wrote down what i could see was wrong and needed correcting. then i carried out the testing and recorded all of my results on eic just for the...
G_FUNK
Thread
codes
customer
help
installation
invoice
needed
pir
write
I cant get my head around the new coding as far as C3 is concerned, if an item eg csa of bonding is compliant with say the 16th but not the 17th do I use C3 and comment complies with prevoius edition and is not urgent, any thoughts please
Hi,
I have just buying a house that has a Ademco alarm. The box is under the stairs (plastic square box with Ademco moulded in) below is a separate keypad, with keys on the right, and leds on the left (zone1, zone2 etc up to 8)
I suspect that the alarm is not working (although the panel is...
Does anyone happen to know what "time interval expired (10223)" means on the the sunny explorer events log. It seems to happen at the same time every morning?? Many thanks in advance
Doing a PIR in a two bed flat, Im wondering what codes to give the following:
1. CCU is in the Kitchen mounted just above the skirting at 200mm height from FFL.
Cheers
Mike
I did a peridodic inspection where the flat has 3 interlinked smoke dectectors which are hard wired in. They all ran out of date in Feb this year, What code would you mark this as?
Hi, I have recently carried out a PIR on a church. The equipotential bonding to the gas and water go back to the sub main in a meeting room where the stop tap and meter are. What code should be assigned as these should go back to the origin?
Has anybody had to use the SMA grid code unlock system?
Looking at the SB4000TL once the code has been entered say via sunny explorer, is it possible then to simply use the grid setting dials (A & B) on the inverter or does it have to be changed using sunny explorer.
Hi guys
has anyone got a table of where to use which code of the new regs c1 c2 c3
in particular what code covers cables less than 50mm in a wall, is it c2 potentially dangerous???
any help will be great :-)
With EICRs replacing PIRs i thought i would start using them but am confused by the new codes
If the installation is safe but does not comply with the new regs (the old code 4) do you put it as C3 requires improvement or just a tick.
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc